background image

InstructIons for:

energy saving lead lamp
11w/230v

Model no:

 ml11.v2

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions 

and properly maintained, give you years of trouble free performance.

1.  saFeTy insTrUCTiOns

2. inTrOdUCTiOn

IMPORTANT:

 

please read THese insTrUCTiOns CareFUlly. nOTe THe saFe OperaTiOnal reQUiremenTs, warnings & CaUTiOns. 

Use THe prOdUCT COrreCTly and wiTH Care FOr THe pUrpOse FOr wHiCH iT is inTended. FailUre TO dO sO may CaUse 

damage and/Or persOnal inJUry and will invalidaTe THe warranTy. please Keep insTrUCTiOns saFe FOr FUTUre Use.

1.1. 

eleCTriCal saFeTy 

  

warning! it is the user’s responsibility to read, understand and comply with the following:

You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and 

all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety 

devices. An rccB (residual current circuit Breaker) should be incorporated in the main distribution board. We also recommend that an rcd

(residual current device) is used with all electrical products. It is particularly important to use an rcd with portable products that are plugged 

into an electrical supply not protected by an rccB. If in doubt consult a qualified electrician. You may obtain a residual current device by 

contacting your sealey dealer. 

you must

 also read and understand the following instructions concerning electrical safety.

1.1.1. the 

electricity at work act 1989

 requires all portable electrical appliances, if used on business premises, to be tested by a qualified  

 

electrician, using a Portable Appliance tester (PAt), at least once a year.

1.1.2. the 

Health & safety at work act 1974

 makes owners of electrical appliances responsible for the safe condition of the appliance

 

and the safety of the appliance operator. 

If in any doubt about electrical safety, contact a qualified electrician.

1.1.3.  ensure the insulation on all cables and the product itself is safe before connecting to the mains  

 power 

supply. see 1.1.1. & 1.1.2. above and use a Portable Appliance tester (PAt).

1.1.4.  ensure that cables are always protected against short circuit and overload.

1.1.5.  regularly inspect power supply, leads, plugs for wear and damage and all electrical connections to  

 

ensure that none is loose. 

1.1.6.  Important: ensure that the product voltage matches the power supply to be used.

1.1.7. 

dO nOT

 pull power plugs from sockets by the power cable.

1.1.8. 

dO nOT

 use worn or damaged leads, plugs or connections. Immediately replace or have repaired by  

 

a qualified electrician. A u.K. 3 pin plug with AstA/Bs approval is fitted. 

 

In case of damage, remove and fit a new plug according to the following instructions (discard old 

 

plug safely). (uK only - see diagram at right). 

 

Ensure the unit is correctly earthed via a three-pin plug. 

 

a)   Connect the green/yellow earth wire to the earth terminal ‘E’.

 

b)  Connect the brown live wire to live terminal ‘L’.

 

c)   Connect the blue neutral wire to the neutral terminal ‘N’.

 

d)  After wiring, check that there are no bare wires, that all wires have been correctly   

 

 

 

connected, that cable outer insulation extends beyond the cable restraint and that the restraint is tight.

High output lighting with even spread of light. low power consumption on both led and fluorescent models saving on energy costs. 

Manufactured to low Voltage directive 73/23/eec. each model is supplied with 5mtr cable and Bs approved plug. Ideal for the professional 

garage/workshop user.

Original Language Version

Ml11.V2   Issue no.1  30/09/13

reCOmmended

 FUse raTing: 3amp

3.  TeCHniCal speCiFiCaTiOns

model no: .............................................ml11.v2

voltage: .................................................230v

power:...................................................11w

lamp Type: ...........................................neon Tube

Tube included: .....................................yes

Cable length: .......................................5mtr

Fitted plug: ...........................................yes

Overall length: ....................................420mm

reolacement Tube: ..............................ml11/12/B

4. OperaTiOn

4.1.

 

to use the lamp, plug it into a mains socket to turn the light on.

4.2.

 

When finished, disconnect the plug from the mains supply, and store it in a safe, dry and childproof location.

© Jack sealey limited

Reviews: