WARNING! Ensure that you read, understand and apply the safety instructions before use.
WARNING! DO NOT attempt to overload the lift. The hydraulic pump is equipped with a safety valve which will prevent an
excessive load from being lifted.
4.1.
Position the lift in a suitable area, checking that the surface on which the lift will stand is solid and flat (preferably concrete).
Stop the platform inadvertently moving by screwing down the ant-roll locks(19).
4.2.
Check that the lift is fully lowered and that the vice jaws are open.
4.3.
Wheel the bike up the lead plate and onto the platform so that the front of the wheel is just beyond the vice. Support bike on the
centre stand.
4.4.
Clamp front wheel in vice to prevent any movement of the bike.
4.5.
Ensure the bike is securely strapped to the platform.
4.6.
Raise the lift by pumping the foot pedal (17).
4.7.
When the lift is raised to the required height ensure the locking bar (13) locates behind one of the four positions of the main platform
(18) so that the lift cannot be inadvertently lowered.
4.8.
When work is complete, check under the lift to ensure that there are no obstructions and that it is safe to lower the unit.
Raise the platform up enough to take the weight off the locking bar (13), lift the locking bar and then
SLOWLY
press the
release valve pedal to
GENTLY
lower the lift.
IMPORTANT!:
The speed of lowering is controlled by the release valve. The more the valve is opened the more rapidly the lift
descends. Ensure the descent is slow and controlled.
4.9.
When the lift is fully lowered, unstrap the bike, open the vice jaws and remove the bike from the lift.
4. OPERATING INSTRUCTIONS
5.1.
When the lift is not in use, it must be stowed in the lowest position to minimise ram and piston corrosion.
5.2.
Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts..
5.3.
Before each use check all parts. If any part of the lift is damaged or suspect remove lift from service and take necessary action to repair.
DO NOT
use the lift if it is believed to have been subjected to abnormal load or shock. Inspect and take appropriate action.
5.4.
Periodically check the ram and piston for signs of corrosion. Clean exposed areas with a clean oiled cloth.
5.5.
The hydraulic oil level is checked as follows:
1) Remove hydraulic unit from lift and stand upright.
2) Remove plug. Correct oil level is up to plug aperture - add hydraulic oil as necessary.
WARNING! Only a good quality hydraulic oil, such as SEALEY HYDRAULIC OIL, must be used. DO NOT use brake fluid.
IMPORTANT!: Only fully qualified personnel should attempt maintenance or repair. Contact your authorised dealer.
5. MAINTENANCE
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE LIFT.
Hydraulic products are repaired by local service agents only. We have service/repair agents in all parts of the UK.
DO NOT RETURN THE PRODUCT TO US.
Please call us on 01284 757500 to obtain the address and telephone number of your local agent.
If the product is under guarantee please contact your dealer.
De-commissioning
Should the lift become completely unserviceable, draw off the oil into an approved container and dispose of the lift and the oil according to local
regulations.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
W e b
Original Language Version
MC455.V2 Issue: 2 - 10/06/13
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
© Jack Sealey Limited
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [email protected] or phone 01284 757500.
