6. MAInTEnAnCE
6.1. Clean and lubricate on a regular basis.
6.2. Regularly check oil level via filler hole. With piston fully down remove filler plug, oil should be level with bottom of filler hole. Top-up as
necessary. Use a good quality jack oil such as Sealey Hydraulic Jack Oil.
do not use brake fluid.
Ensure no dirt enters hydraulic system when filling or removing/replacing components.
6.3.
Always dispose of waste oil according to local authority guidelines. If in doubt consult your local authority.
6.4. Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts.
6.5. Before each use check all parts. If any part of the lift is damaged or suspect, remove the lift from service and take necessary action to repair.
Important: no rESponSIBILItY IS aCCEptED For InCorrECt USE oF tHIS proDUCt.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
Do not rEtUrn proDUCt to US.
Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
de-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the product and
the oil according to local authority regulations.
5.2.7. When the platform has been raised to the working height, turn off the air valve and pass the locking bar (42) through the holes in the underside
of the main platform so that the lift cannot be inadvertently lowered.
5.2.8. When work is done, check under the lift to ensure that there are no obstructions and that it is safe to lower the unit. Remove the locking bar
and then SLOWLY press the release foot pedal to GENTLY lower the lift.
NOTE! The speed of lowering is controlled by the release valve. The more the valve is opened the more rapidly the lift descends. Ensure the decent is
slow and controlled.
5.2.9. When the lift is fully lowered, unstrap the motorcycle, open the vice jaws and remove the cycle from the lift.
7. TROubLEshOOTInG
Lift will not lift load.
1. Release valve not fully closed.
2. Oil level low.
3. Air supply low.
1. Close valve firmly.
2. Top-up to correct level.
3. Min. requirement 120psi.
Lift will not hold load.
1. Release valve not fully closed.
1. Close valve firmly.
Lift will not lift smoothly
or to full height.
1. Oil level low.
2. Air in hydraulic system.
1. Top-up to correct level.
2. Bleed system.
Lift will not lower completely.
1. Release valve not sufficiently open. 1. Slowly open valve further.
notE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTAnT:
No liability is accepted for incorrect use of this product.
WARRAnTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
InFORMATIOn:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sole uK distributor, sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
W e b
Original Language Version
MC365A.V2 Issue: 1 - 10/06/13
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [email protected] or phone 01284 757500.
© Jack Sealey Limited
