3. SPECIFICATION
4. CHARGING
5. OPERATION
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED439
Lens Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190mm
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.4V 4.4Ah Li-ion
Operating Time (High/Standard):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2/6hr
LED:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30W XHP-70 CREE
Lumen Output (High/Standard): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000/800lm
Charging Time: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13hr
4.1.
The lamp may be charged by either the 12V or mains chargers (both supplied)
4.2.
If charging from the mains charger, plug the charger into the mains electrical supply and the pin jack plug into the charging socket (fig.1).
The charging light will show red .
4.3.
If using the 12V charger, insert the plug into the accessory socket. Ensure that the socket is live (some vehicles will require the ignition
switch to be set to the ‘accessory’ or ‘run’ position) and the pin jack plug into the charging socket. The charging light will show red.
4.4.
When the lamp is fully charged, disconnect it from the charger and the charger from the power supply.
4.5.
If not being used, charge the lamp fully every three months to prolong battery life.
5.1.
The on/off switch is used to select the two light levels
First position:
Off
Second position:
Standard Illumination
Third position:
High Illumination
5.2.
The feet can be adjusted by clicking to the required angle
5.3.
The lamp should be charged fully, as in section 4, before being stored out of use.
Battery Removal
Remove the screw securing the back plate and slide the plate out. Disconnect the wiring from the circuit board. Remove
the battery. Dispose of according to local government guidelines
.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s
registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal dispose according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic
Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way.
Contact your local solid waste authority for recycling information.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
fig.1
© Jack Sealey Limited
Original Language Version
LED439 Issue:3(D) - 18/11/16
