instructions for
rechargeable 360° inspection lamp
10 smd led + 3w led lithium-ion
model no:
led360.V2 series
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
1.1.
general
ensure the lamp is fully charged before initial use.
do not
turn the lamp on when it is being charged.
do not
shine directly into your, another person’s or an animal’s eyes.
do not
allow children to use the lamp.
do not
handle or move the lamp whilst it is being charged.
do not
use the lamp if you suspect that the battery or the lamp casing is damaged.
do not
leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently
recharge the battery at least once every six months of non-use.
1.2.
electrical safety for use of charger.
use only the supplied charger plug for connecting lamp to the power supply.
R
warning!
it is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An rccB (residual current circuit Breaker) should be incorporated in the main distribution board. We also recommend that an rcd
(residual current device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an rccB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.2.2.
the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply.
1.2.1.
if worn or damaged
do not
use.
V
important
: check that the voltage marked on the charger plug is the same as the lamp.
1.2.2.
uncoil the cable between charger and the lamp.
do not
pull the charger plug from the mains socket by the lead.
R
warning!
do not
use any other type of charger with this product, other than the supplied mains or car charger. failure to observe
this warning could result in injury and or fire and will invalidate the warranty.
do not
try to take the charger plug apart.
do not
use the charger plug to charge or power any other electrical item.
do not
get the charger wet, or use in wet, damp conditions (for indoor use only).
1.3.
battery safety
R
warning!
To reduce the risk of burns or fire:
do not
attempt to open, disassemble, modify or service the battery pack.
do not
crush, puncture, short external contacts or dispose of in fire or water.
do not
expose to temperatures above 60°c (140°).
replace only with the battery pack designated for this product.
recycle or dispose of used battery as stipulated by local regulation.
if the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. if it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention
refer to
instruction
manual
led360.V2 series | issue 2(sP) - 15/03/16
Original Language Version
© Jack sealey limited
