![background image](http://html1.mh-extra.com/html/sealey/led130t-v2/led130t-v2_instructions_1224810001.webp)
1.1. PLUG & MAINS POWER SUPPLY
WARNING! It is the owner’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure that they are safe before using. You must inspect power supply leads, plugs and all
electrical connections for wear and damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. An
RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device)
is used with all electrical products. It is particularly important to use an RCD together with portable products that are plugged into an electrical supply not
protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
NOTE:
110 volt lights are usually operated by connecting to a transformer or
a generator. Check to ensure all supply equipment is compatible with the rating of the light.
1.1.1. The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition
of the appliance and the safety of the appliance operator.
If in any doubt about electrical safety, contact a
qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the power supply.
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage and especially
power connections to ensure that none is loose.
1.1.6.
Important:
Ensure the voltage marked on the product is the same as the electrical power supply to be used
and check that plugs are fitted with the correct capacity fuse.
A 13amp plug may require a fuse smaller than 13amps for certain products, see fuse rating listed right (fig.1).
1.1.7.
Important:
For use of a 110 volt lights - ensure that the transformer or generator is adequately rated.
1.1.8.
DO NOT
pull or carry the appliance by the power cable.
1.1.9.
DO NOT
pull plugs from sockets by the power cable.
1.1.10.
DO NOT
use worn or damaged leads, plugs or connections. Immediately replace or have repaired by a qualified
electrician. A U.K. 3 pin 13amp or 110 volt plug with ASTA/BS approval is fitted. In case of damage, cut off and fit
a new plug according to the following instructions (discard old plug safely). (UK only - see diagrams right).
Ensure the unit is correctly earthed via a three-pin plug. FOR 230 VOLT 13AMP PLUG SEE fig.1, FOR
110 VOLT PLUG SEE fig.2.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the
cable external insulation extends beyond the cable restraint and that the restraint is tight.
1.1.11.
Cable extension reels
. When a cable extension reel is used it should be fully unwound before connection.
A cable reel with an RCD fitted is recommended since any product which is plugged into the cable reel will be
protected. The section of the cores of the cable is important and should be at least 1.5mm², but to be absolutely
sure that the capacity of the cable reel is suitable for this product and for others that may be used in the other
output sockets, we recommend the use of 2.5mm² section cable.
1.2. LIGHT WIRING
WARNING! Ensure all cables are disconnected from the power supply before attempting following:
Should the lamp need to be re-wired, contact a qualified electrician. The procedure cable into the lamp, proceed
as follows: Remove back cover of terminal box, located at the rear of the lamp, to expose the connection block
and wires, see fig.3. When wired, check that the weather proofing seal is correctly located in the back cover
recess and then replace the back cover.
1.3. GENERAL SAFETY
WARNING! Disconnect light from the power supply before changing accessories, servicing or performing
any maintenance.
Maintain the light in good condition. Repairs must only be undertaken by a qualified electrician
(use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only, unauthorised parts may be
dangerous and will invalidate the warranty.
Keep a minimum distance of 1 metre from the front of light to the surface which is to be
illuminated.
Locate the light in an adequate area for its function, keep area clean and tidy and free from
unrelated materials.
If using an extension lead,
the cable must be fully unwound from the drum
.
The lights are weather proof and may be used outdoors. Ensure any extensions and plugs
are weatherproof.
If using a tripod, ensure that the legs are fully extended and are standing on a level, solid
surface. Ensure that the cable is safely routed.
Allow power cables to run down the length of the light stand to the floor.
DO NOT
allow
power cables to hang from lights above floor level.
DANGER! DO NOT direct the light into a person’s eyes.
These models have a very
intense light output which, if incorrectly used, could cause eye
damage.
DO NOT
touch the light when operating. If needed allow to cool before touching.
DO NOT
handle halogen bulbs as the natural oil from hands will shorten the bulb's life.
Handle only with a soft dry cloth.
INSTRUCTIONS FOR:
TELESCOPIC / PORTABLE 18 SMD
FLOODLIGHTS 230V/110V
fig.3
fig.2
230V
FUSE RATING - 3AMP
fig.1
© Jack Sealey Limited
Original Language Version
LED130T.V2, LED130TD.V2, LED130110T.V2, LED130110TD.V2 Issue: 1 - 30/07/14
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
MODEL No's:
LED130T.V2 LED130TD.V2 LED130110T.V2 LED130110TD.V2