![background image](http://html.mh-extra.com/html/sealey/led036/led036_instruction-manual_1227660001.webp)
InstructIon MAnuAL for:
UNDER BONNET CORDLESS 36 SMD
RECHARGEABLE LAMP LITHIUM-ION
MODEL NO : LED036
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give
you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version
LED036 Issue: 1 - 13/02/13
© Jack sealey Limited
1. SAFETY
1.1. GENERAL
WARNING!
Disconnect lamp from mains power
before performing any maintenance.
DO NOT
shine lamp directly into your, other person’s
or animal’s eyes.
DO NOT
allow children to use the lamp.
Maintain the lamp in good condition.
DO NOT
use the lamp if the lamp if damaged.
When not in use store the light in a safe, dry,
childproof location.
WARNING!
Ensure Health and safety, local authority
and general workshop practice regulations are
adhered to when using this light.
Wear eye protection. A full range of safety equipment
is available from your sealey dealer.
Wear suitable clothing to avoid snagging.
DO NOT
wear jewellery and tie back long hair.
Account for all tools being used and
DO NOT
leave
them in or near the engine.
1.2. ELECTRICAL SAFETY FOR USE OF
TRANSFORMER.
USE ONLY THE SUPPLIED
TRANSFORMER
PLUG FOR CONNECTING LAMP TO THE POWER
SUPPLY.
WARNING!
It is the user’s responsibility to read, understand and
comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installa-
tion of appropriate safety devices. An rccB (residual current circuit
Breaker) should be incorporated in the main distribution board. We also
recommend that an rcD (residual current Device) is used with all
electrical products, particularly portable equipment which is plugged into
an electrical supply not protected by an rccB.
You must
also read and understand the following
instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989
requires all portable electrical
appliances, if used on business
premises, to be tested by a qualified electrician, using a Portable
Appliance tester (PAt), at least once a year.
1.2.2. The Health & Safety at Work Act 1974
makes owners of electri-
cal appliances responsible for the safe condition of the appliance and
the safety of the appliance operator.
If in any doubt about electrical
safety,
contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the transformer plug, cable and connector for
wear and damage to ensure items are safe before
connecting to the mains power supply. If worn or
damaged
DO NOT
use.
Important: check that the voltage marked on the
transformer plug is the same as the power supply to
be used.
uncoil the cable between transformer plug and lamp.
DO NOT
pull the transformer plug from the mains
socket by the lead.
DO NOT
use any other type of transformer with this
product.
DO NOT
try to take the transformer plug apart.
DO NOT
use the transformer plug to power any other
electrical item.
DO NOT
get the transformer plug wet, or use in
wet, damp conditions (for indoor use only).
WARNING!
NEVER
substitute a standard 13amp
3 pin plug, or any other type of plug, for the
transformer plug.
this transformer plug reduces and rectifies the mains
voltage (230 volts Ac) to
12 volts DC.
Fig.1
Fig.2
WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and sit-
uations that may occur. It must be understood that common sense and caution are factors which must be applied by the operator.