p
WARNING! Ensure you read, understand and apply safety instructions for use.
4.1. Assembly.
4.1.1. Screw in the backing pad into the spindle nut (fig.3). Tighten using the supplied spanner.
4.1.2. Apply the appropriate sanding pad to the backing pad. Use only pads with speed ratings equal to or
higher than the speed rating of the sander.
DO NOT
use cloth backed sanding pads.
4.1.3. Connect the air supply to the sander and press the trigger, check that the sander is working correctly.
4.1.4. The air flow may be regulated by turning the air control valve on the side of the handle (fig.3).
4.2. Operation.
4.2.1. Always use a sanding pad appropriate for the job.
4.2.2. Work progressively from coarse grades to finer grades.
7
DO NOT
go from coarse to fine in one step as it
may be difficult to remove swirl marks left by the
coarser grit.
7
DO NOT
apply excessive pressure, let the
sander do the work for you.
4.2.3. Start the sander and bring the sanding disc to
the work surface slowly and evenly. Move the
sander back and forth in overlapping motions.
4.2.4. Remove the sanding disc from the work surface
before stopping the sander. Regularly check the
sanding pad for wear and always change a
cracked or damaged pad.
7
DO NOT
allow the sander to run in “idle rotation”
for an extended period of time as this will
shorten the life of the bearings.
p
WARNING!
Disconnect sander from air supply before changing accessories, servicing or performing
maintenance.
Replace or repair damaged parts.
Use genuine parts only. Non-authorised parts may be
dangerous and will invalidate the warranty.
5.1.
Lubricate the air sander daily with a few drops of good grade air tool oil such as Sealey ATO500S or
ATO1000S, dripped into the air inlet before use.
5.2.
Clean the sander after use and change pads when required.
5.3.
Loss of power or erratic action may be due to the following:
a)
Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose
connectors. To remedy check the air supply and follow instructions in section 3.
b)
Grit or gum deposits in the sander may also reduce performance. If your model has an air strainer
(located in the area of the air inlet), remove the strainer and clean it. Flush the sander out with gum
solvent oil or an equal mixture of SAE No.10 oil and kerosene. Allow to dry before use.
If you continue to experience problems, contact your local Sealey service agent.
5.4.
For a full service contact your local Sealey service agent.
5.5.
When not in use, disconnect from air supply, clean sander and store in a safe, dry, childproof location.
4. OPERATION
5. MAINTENANCE
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Risk of Hand Arm Vibration Injury.
Air Palm Orbital Sanders, Model No’s. GSA08 & GSA09, when operated in accordance with these instructions and tested in
accordance with BS EN 28662-1:1993, ISO 8662-1:1988 and BS EN ISO 28927-3:2009 in the following vibration emission
declared in accordance with BS EN12096:1996.
Measured vibration emission value:
8.06m/s²
Uncertainty value:
3.22m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 1 hour 34 minutes in any 8
hour period.
This duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
fig.3
(GSA08)
Original Language Version
GSA08,GSA09 Issue: 1 - 09/09/11
Parts support is available for this product.
To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk,
email [email protected] or phone 01284 757500.
