1
fig.1
WARNING! DO NOT
sand any materials containing asbestos.
DO NOT
switch the polisher on whilst the head is in contact with the work piece and avoid unintentional starting.
DO NOT
get the polisher wet or use in damp or wet locations or areas where there is condensation.
DO NOT
allow untrained persons to operate the polisher.
DO NOT
operate the polisher when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT
use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
DO NOT
leave the polisher operating unattended.
DO NOT
carry the polisher with your finger on the power switch.
DO NOT
pull the cord to remove the plug from the power supply.
Use a qualified person to lubricate and maintain the polisher.
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
lEAD PAInT WArnIng!
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is
toxic and must therefore be avoided. The following action must be taken before using machine as a sander:
1.
User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
2.
DANGER!
Keep all persons and pets away from the working area. The following are particularly vulnerable to the effects of lead
paint dust: Expectant women, babies and children.
3.
We recommend personal protection by using the following safety items:
A) Paint Spray Respirator (Sealey ref. SSP1699) B) PE Coated Hooded Coverall (Sealey ref. SSP266). C) Latex Gloves (Sealey
ref. SSP24).
4.
Take adequate measures to contain paint dust, flakes and scrapings. Wear safety equipment, as in (3) above and thoroughly clean
all areas when task is complete.
5.
Ensure the paint waste is disposed of in sealed bags or containers according to local regulations.
Risk of hand Arm Vibration Injury.
The ER1700P.V2 Variable Speed
Polisher, when operated in accordance with these instructions and tested in accordance with
BS EN
28662-1:1993, ISO 8662-1:1988
and
BS EN ISO 8662-8:1997
results in the following vibration emission declared in accordance with
BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . 10.9m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . 4.6m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 51 minutes in any 8 hour period.
This duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
3. TEChNICAL SpECIFICATIONS
2. INTRODUCTION
Features variable speed control ranging from 0 to 2800rpm. Two level gear system reduces output speed, still maintaining a high torque level.
Alloy bevel gear head with composite motor housing. Spindle lock for easy pad removal. Supplied with Ø150mm hook-and-loop backing pad,
polishing bonnet and side handle.
4. CONTENT & ASSEmBLY
4.1.
Content
4.1.1. Check the contents of the carton. If any item is missing or damaged contact
your supplier immediately.
fig.1. 1: polisher Unit
2: pad
3: Side handle
4: Lambs Wool Bonnet
4.2.
Assembly
WARNING! Ensure unit is not plugged into mains before attempting any assembly.
4.2.1. Attach the side handle (fig.1.3). Note: there is a mounting hole on either side to suit the application and/or operator.
4.2.2. To attach the hook and loop pad (fig.1.2), place it on to the spindle and turn clockwise. Lock the spindle by pressing the locking button,
and tighten pad (fig.2)
4.2.3. To fit the polishing bonnet:
Fit the polishing bonnet over the secured hook and loop pad, using the pull cord tighten the bonnet and tie a bow to secure, tuck the
loose ends of the bow neatly under the bonnet.
model . . . . . . . . . . . . . . . . . . . . . . . ER1700p.V2
Nominal Power Rating . . . . . . . . . . . . .800Watts
Power Input. . . . . . . . . . . . . . . . . . . . . . . . . 230V
No Load Speed. . . . . . . . . . . . . . . . . . . 2800rpm
Pad Size . . . . . . . . . . . . . . . . . . . . . . . . . 150mm
Noise - Power . . . . . . . . . . . . . . . . . . . . . . . 96dB
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 83.8dB
Spindle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .M14
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2Kg
3
2
4
Original Language Version
ER1700P.V2 Issue: 2 - 19/02/10
