2. tEcHnical SPEciFicatiOnS
Before use check abrasive pad condition. if worn or damaged replace immediately.
WaRninG!
Always wear approved eye or face protection when operating the sander.
if dust is generated, use face, dust, or respiratory protection in accordance with cosHH regulations.
depending on task, sander noise level may exceed 85dB in which case wear safety ear defenders.
remove ill fitting clothing, ties, watches, rings, other loose jewellery, and contain and/ or tie back long hair.
Wear appropriate protective clothing and keep hands and body clear of the sanders working parts.
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
check moving parts alignment on a regular basis.
ensure the workpiece is correctly secured before operating the sander. never hold workpiece by hand, and check the work
piece to ensure there are no protruding nails, screws, stones, etc.
Avoid unintentional starting.
DO nOt
force the sander to achieve a task it was not designed to perform.
DO nOt
operate sander if any parts are damaged or missing. this may cause failure or possible injury.
WaRninG!
DO nOt
sand any materials containing asbestos.
DO nOt
carry the sander by the electrical cable or dust extraction hose.
DO nOt
get the sander wet or use in damp or wet locations.
DO nOt
use these models with water, these models are dry sanders only.
DO nOt
operate sander if you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO nOt
use where there is flammable liquids, solids or gases such as paint solvents, including waste wiping or cleaning
rags etc.
DO nOt
leave the sander operating unattended.
DO nOt
carry the sander with your finger on the power switch.
When not in use disconnect from the mains power supply and dust free system and store in a safe, dry, childproof area
WARNING! DO NOT
allow uncontrolled discharge of dust waste thus polluting the environment.
1.3 lEaD Paint WaRninG!
Paint once contained lead as a traditional ingredient. contact with the dust from the removal of such paint is toxic and
must therefore be avoided. the following action must be taken before using the sander on a surface that you suspect
may have contained lead in the paint.
1. user must determine potential hazard relating to age of paint to be removed. (modern paints do not have lead
content).
2.
DanGER!
Keep all persons and pets away from the working area. the following persons are particularly vulnerable
to the effects of lead paint dust:
Expectant women, babies and children.
3. We recommend personal protection by using the following safety items:
a
) Paint spray respirator (our ref ssP1699, ssP1604)
b
) Pe coated Hooded coverall (our ref ssP267).
c
) latex Gloves (our ref ssP24).
4. take adequate measures to contain the paint dust, flakes, and scrapings.
5. continue to wear safety equipment as in (3) above, and thoroughly clean all areas when task is complete. ensure
paint waste is disposed of in sealed bags or containers.
these er & em models are of the vertical type for heavy duty sanding applications. each sander has a tough composite body
shell with a trigger operating switch and a power lock control.
models er150d/dfs.V2 & em110d/dfs are dust free sanders for connecting to a dust free system.
Model: . . . . . . . . . . . .ER150D.V2 . . . . . . . . ER150D/DFS.V2 . . . . . . . . . . . . . . . . EM110.V2 . . . . . . . . . . . . . . EM110/DFS.V2
free speed (rpm) . . . . . . . . 8000 . . . . . . . . . . . . . . . . . . 8000 . . . . . . . . . . . . . . . . . . . . 8000 . . . . . . . . . . . . . . . . . . . . . . 8000
orbit Ø (mm) . . . . . . . . . . . . . . . 8 . . . . . . . . . . . . . . . . . . . . . 8 . . . . . . . . . . . . . . . . . . . . . . n/a . . . . . . . . . . . . . . . . . . . . . . . . n/a
Pad size (mm) . . . . . . . . . . . . 150 . . . . . . . . . . . . . . . . . . . 150 . . . . . . . . . . . . . . . . . .210x115 . . .210x115 accepts 4-1/2” paper
thread size (ufn) . . . . . . . 5/16” . . . . . . . . . . . . . . . . . . 5/16” . . . . . . . . . . . . . . . . . . . . 5/16” . . . . . . . . . . . . . . . . . . . . . . 5/16”
Power (Watts) . . . . . . . . . . . . 450 . . . . . . . . . . . . . . . . . . . 450 . . . . . . . . . . . . . . . . . . . . . 500 . . . . . . . . . . . . . . . . . . . . . . . 500
Power input . . . . . . . . 230V-1.8A . . . . . . . . . . . . . .230V-1.8A . . . . . . . . . . . . . . . . 230V-2.0A . . . . . . . . . . . . . . . . . . 230V-2.0A
Original Language Version
em110.V2, em110/dfs.V2,
er150d.V2, er150d/dfs.V2 issue: 3 - 07/04/10
