Unpack the product and check that there are no missing or damaged parts. If you do experience a problem contact your supplier immediately.
Your kit should consist of the following: Spot welder and pneumatic air cooled clamp - 130mm arms (water cooled, 9500 only) and standard
electrodes - with cables. Filter-pressure regulator, gauge and electrovalve (compressed air supply). Water cooler (9500 only). Trolley.
SPECIFICATIONS:
ElectroSpot 8000 ElectroSpot 9500.V2
Power supply . . . . . . . . . . . . . . . . . .400V(380V-415V) . . . .400V(380V-415V)
- 1ph-50/60Hz
- 1ph-50/60Hz
Power supply - water cooler . . . . . . . . . . . . . . . . . .N/A . .230V - 1ph-50/60Hz
Electrical protection class . . . . . . . . . . . . . . . . . . . . . .I . . . . . . . . . . . . . . . . .I
Insulation class . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H . . . . . . . . . . . . . . . .H
Casing protection class . . . . . . . . . . . . . . . . . . . . .IP22 . . . . . . . . . . . . . .IP22
Dimensions with trolley (LxWxH) . . .650x400x1100mm . . . .650x400x1100mm
Output
ElectroSpot 8000 ElectroSpot 9500.V2
Secondary no-load voltage (U
0
max) . . . . . . . . . . .8.6V . . . . . . . . . . . . . .8.6V
Max welding current (I
2
max) . . . . . . . . . . . . . . . .4.5kA . . . . . . . . . . . . . . .7kA
Capacity (low carbon steel) . . . . . . . .max. 1.5+1.5mm . . . . . . . .max. 3+3mm
Duty cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3% . . . . . . . . . . . . . .5.5%
Spots/hour on steel 1+1mm - air cooled clamp . . . .200 . . . . . . . . . . . . . . .200
water cooled arms . . . .N/A . . . . . . . . . . . . . . .400
water cooled arms and clamp . . . .N/A . . . . . . . . . . . . . .1000
Max. force at electrodes . . . . . . . . . . . . . . . . . . .120kg . . . . . . . . . . . . .120kg
Min. coolant flow . . . . . . . . . . . . . . . . . . . . . . . . . .N/A . . . . . . . . . . . . . .2l/m
Automatic spot welding current adjustment.
Automatic spot welding time adjustment to suit sheet thickness and clamp used.
Input
ElectroSpot 8000 ElectroSpot 9500.V2
Max welding power (Smax) . . . . . . . . . . . . . . . .39kVA . . . . . . . . . . . . .58kVA
Rated power at 50% (Sn) . . . . . . . . . . . . . . . . . .6.7kW .(water cooled)13.0kW
Power factor at Smax (Cos
ϕ)
. . . . . . . . . . . . . . . .0,65 . . . . . . . . . . . . . .0.65
Delayed mains fuses . . . . . . . . . . . . . . . . . . . . . . 25A . . . . . . . . . . . . . . .32A
Automatic mains switch . . . . . . . . . . . . . . . . . . . . .25A . . . . . . . . . . . . . . .32A
Mains cable (L
≤
4m) . . . . . . . . . . . . . . . . . .3x2.5mm
2
. . . . . . . . . . . .3x4mm
2
Water cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . .N/A . . . . . . . . . . . . .270W
3. CONTENTS & SPECIFICATIONS
2. INTRODUCTION
An air supply is required to operate the pneumatic clamps. See fig. 1 for the recommended hook-up.
4.1.
Ensure that the air valve is in the "off" position before connecting to the air supply.
4.2.
The pneumatic clamps require a compressed air supply of 6 to 8 bar connected to the filter-regulator at the rear of the welder.
4.3.
!
WARNING!
Ensure that the air supply does not exceed 8 bar while operating the welder. Too high an air pressure and/or
unclean air will shorten the product life, due to excessive wear, and may be dangerous,
causing possible damage and/or personal injury.
4.4.
Drain the air tank daily. Water in the air line will damage the clamp.
4.5.
Clean the compressor air inlet filter screen weekly.
4.6.
Line pressure should be increased to compensate for
unusually long air hoses (over 8 metres). The minimum
hose diameter should be 10mm I.D. and fittings must
have the same inside dimensions.
4.7.
Keep hoses away from heat, oil and sharp edges.
Check hoses for wear, and make certain that
all connections are secure.
4. AIR SUPPLY
5. TROLLEY ASSEMBLY
fig. 1
Microprocessor controlled power unit with push-button control automatically recognises which welding accessories are fitted and adapts power
and duration characteristics for optimum results. Includes operator override. Features pulse facility for welding high stress materials. Check-
panel indicates machine status including: supply, thermostat, supply over/under voltage. Piggy-back water-cooler cools both power cables and
arms for maximum duty-cycle (9500 only). Supplied with pneumatic pincers and set of arms. Includes trolley.
A diagram showing the assembly of the trolley may be found at the end of these Instructions.
!
WARNING! DO NOT
attempt to put the spot welder onto the trolley until you are certain that all the trolley assembly fixings are tight and
that the wheels have been correctly mounted.
ELECTROSPOT 8000
(With ‘optional’ gun 801045)
ElectroSpot 8000/9500.V2 - 2 - 040903
Summary of Contents for ELECTROSPOT 8000
Page 17: ......
