Input Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 volt
Speed Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8000 to 30000rpm
Speed Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stepless control
Collet Capacities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3mm and 3mm
Twist Drills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.3mm and 3mm
Mounted Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10pc
Diamond Tipped Engraving Heads. . . . . . . . . . . . . . . . . . . . . . . . . 2 x 1.8mm
Sanding Cylinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12.7mm x 12.7mm
2. TECHNICAL SPECIFICATION
3.1
Check contents against the following list. If any
item is missing or damaged contact your
supplier immediately. Refer to Fig. 2.
1)
Grinding wheel.
2)
Sanding shank (12.7 x 12.7mm).
3)
Spherical diamond cutter.
4)
Tapered diamond cutter.
5)
Mandrel for cut-off wheel.
6)
Mandrel for felt wheel.
7)
Sanding band (12.7 x 12.7mm).
8)
Sanding discs (20 x 0.35mm).
9)
Cut-off wheels.
10)
Felt wheel (22 x 7mm).
11)
Felt wheel (12.7 x 7mm).
12)
Dressing stone (20 x 10 x 10).
13)
Brass collet (2.3mm).
14A)
HSS twist drill (2.3mm)
14B)
HSS twist drill (3mm).
15)
Wrench (9.7mm).
Electric grinder.
3. CONTENTS
Fig. 1
Fig. 2
4. OPERATING INSTRUCTIONS
4.1
Connection
4.1.1
Ensure that ON/OFF switch is in the OFF position. ‘OFF’ is shown as ‘0’ on the switch plate. Refer to Fig. 1.
4.1.2
Insert the plug on the end of the tool cable into a mains socket.
4.2
Fitting Accessories
4.2.1
Ensure the tool is switched off and unplugged from the mains supply.
4.2.2
Press the spindle lock button and slowly turn the collet nut until the spindle lock engages. Refer to Fig. 1.
4.2.3
Retain pressure on the spindle lock button and turn the collet nut anticlockwise to open the collet.
NOTE: Never press the spindle lock button when the tool is running.
4.2.4
The required accessory may now be fitted into the collet. Fully insert the accessory shaft to reduce the risk of bending in use. Tighten
the collet nut firmly. Finally, release the spindle lock button.
4.2.5
To change collets, proceed as in paragraphs 4.2.1 to 4.2.3 but continue to unscrew the collet nut until it can be removed from the
spindle. Change collets and replace the collet nut.
4.2.6
Select the speed required on the variable speed control. Small accessories require high speed and large accessories low speed. If in
doubt, start on a low setting and gradually increase the speed until the best performance is obtained.
4.2.7
Check that the ON/OFF switch is set to OFF and then connect the tool to the mains supply. Set the ON/OFF switch to ON.
NOTE: DO NOT
switch ON with a tool bit touching the workpiece. Always allow a bit to reach required speed before applying it to the workpiece.
5.1
Cleaning
Keep the tool ventilation slots clean and free from obstructions. If available, blow compressed air into the vents to clear any internal
dust. Safety goggles
MUST
be worn when undertaking this process. Keep the drill outer case clean and free from grease. Wipe it
down with a damp cloth.
DO NOT
wash with water or use solvents or abrasives.
5.2
Other
To service the tool contact your local Sealey service agent.
Declaration of Conformity
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Tools.
Signed by Steve Buckle
Date 15th February 2006
E540 Multipurpose Rotary Tool
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37EEC Machinery Equipment Directive
5. MAINTENANCE
E540 - (1) - 150206
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
