20V 2AH LITHIUM-ION CORDLESS NUT
RIVETER
MODEL NO:
CP316
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
TANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH
HE
P
PR
O
ODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE
ER
S
SON
NAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL
SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance
Test)
tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is
fi
tted with the
correct fuse - see fuse rating in these instructions.
DO
NOT
pull or carry the appliance by the power cable.
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a
fi
rm grip on the plug.
DO
NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
quali
fi
ed electrician.
1.1.4.
This product is
fi
tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a quali
fi
ed electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO
NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a quali
fi
ed electrician.
1.2. BATTERY CHARGER SAFETY INSTRUCTIONS
WARNING! DO
NOT
use the charging base to charge any battery other than that required for the tool. Other types of batteries may
explode!
Inspect the plug, cable and the charging base for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged
DO NOT
use, immediately replace, or contact a quali
fi
ed electrician.
Check cables are always protected against short circuit and overload.
Uncoil the power cable between the plug and the charging base before use.
DO NOT
pull or carry the charging base by the charger power lead, or pull the plug from the mains socket by the power lead.
DO NOT
use any other type of transformer with the charging base.
DO NOT
try to open or dis-assemble the plug or charging base.
DO NOT
use the plug to power any other electrical item.
Disconnect the charging base from the mains power supply when not in use.
DO NOT
expose the charging base to damp or wet conditions (for indoor use only).
DO NOT
operate the charging base if it has been dropped, or has received a sharp knock, or is damaged. Contact an authorised
service
agent.
DO NOT
dismantle the charging base as this may cause damage or personal injury and will invalidate your warranty.
DO NOT
insert foreign objects or material into the slot reserved for the battery.
DO NOT
immediately charge a second battery. Consecutive charging will overheat the charging base. Allow the unit to cool for
15 minutes before charging the next battery.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
Ensure that cables are always protected against short circuit and overload.
Recommended fuse rating
3 Amp
CP316 Issue 1 16/03/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear ear
protection