Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
1. SAFETY
1.1. GENERAL SAFETY
9
Follow all workshop safety rules, regulations and conditions when using the wrench.
9
Remove the battery pack from the wrench before servicing or performing any maintenance.
9
Maintain the wrench and battery pack in good condition. Check moving parts for alignment on a regular basis.
9
Replace or repair damaged parts.
Use an authorised service agent and recommended parts only. Unauthorised parts may be dangerous
9
and will invalidate the warranty.
9
Ensure the wrench is locked before installing the battery pack.
9
Keep the wrench, battery pack and charger clean for optimum performance.
9
Keep the work area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.
9
Ensure that battery pack is correctly inserted into the wrench handle and latched in place before operating wrench.
WARNING!
When working around vehicle brake systems we recommend that you wear suitable respiratory protection owing to the
possible Presence of asbestos dust from brake linings.
8
U
se only impact sockets which are specifically designed for use with an impact wrench.
8
Avoid unintentional starting.
8
Wear approved safety eye/face shield, ear defenders and hand protection.
8
Remove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
8
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
8
Keep children and unauthorised persons away from the work area.
8
DO NOT
operate the wrench if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
use the wrench unless you have been instructed in its use by a qualified person.
8
DO NOT
operate the wrench where there are solvent fumes or flammable gases, liquids or solids.
8
DO NOT
leave the wrench operating unattended.
8
DO NOT
carry wrench with your finger on the trigger. Keep direction switch in ‘locked’ position when not in use.
8
DO NOT
use the wrench for a task it is not designed to perform.
8
DO NOT
operate the wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the wrench or battery charger wet or use in damp or wet locations.
9
Keep wrench and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 40°C (104°F).
1.2. BATTERY SAFETY INSTRucTIONS
9
Charge the battery pack prior to first use. The battery pack will have been shipped in a low charge state.
9
Use only the charger provided to charge the battery pack.
8
DO NOT
charge the battery pack when room temperature is below 10°C (50°F) or above 40°C (104°F).
8
DO NOT
attempt recharging the pack by means of an engine generator or a DC power source.
8
DO NOT
short-circuit the battery pack by touching both terminals at the same time with a metal object, or your fingers etc.
8
DO NOT
store battery pack or wrench in locations where the temperature may exceed 40°C (104°F) e.g. in outside sheds, above
heaters etc.
1.3. MAINS POWER ELEcTRIcAL SAFETY
(In relation to the battery charger)
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must
check all electrical products, before use, to ensure that they are safe. You must
inspect power cables, plugs, sockets and any
other connectors for wear or damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a
Residual Current Device (RCD) be used. It is particularly important to use an RCD with portable products that are plugged into a supply
that is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting
your Sealey stockist.
You must
also read and understand the following instructions concerning electrical safety.
1.3.1. The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.3.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.3.1 and 1.3.2
and use a Portable Appliance Tester.
1.3.4. Ensure that cables are always protected against short circuit and overload.
1.3.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure none is loose.
1.3.6. Important:
Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the
Original Language Version
© Jack Sealey Limited
Refer to
Instructions
InSTRUCTIonS FoR:
cORDLESS IMPAcT WRENch 26v 4Ah LI-ION
1/2” SquARE DRIvE (680NM) 500LB.FT
3/4” SquARE DRIvE (816NM) 600LB.FT
MoDEL no:
cP2612 (1/2”) , cP2634 (3/4”)
Wear Ear
Protection
Wear Eye
Protection
Wear Protective
Gloves
Wear a Mask
CP2612, CP2634 Issue1 - 06/12/17
