1.3.9.
DO NOT
use worn or damage cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a competent electrician. When an ASTA/BS approved
UK 3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Ensure that the double insulated charger is correctly connected via a three-pin plug, as
follows:
a) Connect the Brown live wire to live terminal ‘L’.
b) Connect the Blue neutral wire to the neutral terminal ‘N’.
c) After wiring, check that there are no bare wires, that all wires have been
connected correctly, that the cable outer insulation extends past the cable clamp and
that the clamp is tight. Note that the earth pin ‘E’ remains unconnected.
1.4. BATTERY CHARGER SAFETY INSTRUCTIONS
WARNING!
DO NOT
attempt to charge any battery other than that supplied for the wrench.
Other types of batteries may explode!
All mains electrical supply safety features must be followed as described in 1.3 above.
Disconnect the charger from the electrical supply when not in use.
DO NOT
charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
DO NOT
expose the charger to damp or wet conditions.
DO NOT
pull or carry the charger by the power lead.
DO NOT
operate the charger if it has been dropped, or has received a sharp knock, or is
damaged. Take the charger to an authorised agent for repair or obtain a replacement.
DO NOT
dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
DO NOT
insert foreign objects or material into the hole reserved for the battery pack.
DO NOT
recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger.
Allow the unit to cool for 15 minutes before charging the next pack.
DO NOT
attempt to connect two chargers together.
Store the charger in the same manner as the battery pack in 1.2.
RECOMMENDED
FUSE RATING:
5AMP
2. INTRODUCTION & SPECIFICATION
fig.1
Powerful cordless ratchet wrench with hardened steel anvil and twist-to-reverse
mechanism. Finger operated trigger incorporated in housing. Textured soft grip helps
reduce vibration. Features built-in LED work light for use in low-light areas. Suitable for
workshop applications. Includes 14.4V 2Ah Ni-MH battery pack and 80 minute mains
charger.
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CP2144MH
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4V 2Ah Ni-MH
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8"Sq
Maximum Torque: . . . . . . . . . . . . . . . . . . . . . . . . . .48Nm(35lb.ft)
Replacement Battery: . . . . . . . . . . . . . . . . . . . . . . CP2144MHBP
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2.1kg
© Jack Sealey Limited
Original Language Version
3. OPERATING INSTRUCTIONS
IMPORTANT WARRANTY INFORMATION:
The battery pack fitted to this cordless tool is considered to be a consumable
item and its ability to accept charge will reduce over time. We will warranty it
against mechanical and electrical defect for a period of one year - this does not
cover fair wear and tear. If the battery is not properly charged before first use,
or regularly conditioned, its capacity will diminish. Under these circumstances
we will not replace the battery pack even if it is less than one year old.
3.1. CHARGING THE BATTERY PACK
3.1.1. Remove the battery pack (fig.1F) from the wrench, by depressing the two
side release clips (fig.1F).
WARNING!
DO NOT
touch metal terminals.
3.1.2. Place wrench in carry case and remove the battery charger.
3.1.3. The battery pack and charger positive (+) and negative (-) terminals are
marked. Align the terminals correctly and insert the battery into the slot.
3.1.4. Switch on the electrical supply to the charger and the green LED will light.
3.1.5. Insert the battery pack and the red LED will flash, showing that charging is
taking place.
Note:
The battery pack is designed so that it will only enter the charger unit the correct
way. When placed in the charger, a very slight downward pressure will seat the
pack firmly into the power terminals.
3.1.6. When the red and green LEDs stay on together, this indicates that charging is
complete. The battery pack is now ready for use.
3.1.7. After removing the battery, disconnect the charger from the electrical supply and
store it in the carry case.
Note: The first charge and several subsequent charges will take longer than usual
until the battery reaches optimum performance, after that the usual charge
time will take approximately 80 minutes.
CP2144MH Issue: 1 - 09/06/16
