Ø125MM CORDLESS ORBITAL POLISHER 20V
- BODY ONLY
MODEL NO:
CP20VOP
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
polisher.
9
Familiarise yourself with the application, limitations and potential hazards of the polisher.
WARNING!
Disconnect from the mains power and ensure that the pad is at a complete standstill before changing accessories,
servicing or performing any maintenance.
9
Maintain the polisher in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING!
Keep all guards and holding screws in place, tight and in good working order.
9
Check regularly for damaged parts. A guard or any other part that is damaged must be repaired/replaced before the polisher is next
used.
9
Use the polisher in a suitable work area and keep the area clean and tidy and free from unrelated materials. Ensure that there is
adequate lighting.
9
Keep the polisher clean for best and safest performance.
9
Before each use check all attachments for condition. If worn or damaged replace immediately.
9
Ensure that there are no flammable materials near the work area.
WARNING!
Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
9
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Avoid unintentional starting.
8
DO NOT
use the polisher for any purpose other than that for which it is designed.
8
DO NOT
operate the polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT
switch the polisher on until the head is in contact with the panel and switch the unit off before removing the head from the
panel.
8
DO NOT
use the polisher with abrasive cleaners or rubbing compounds as excessive paint removal may result.
8
DO NOT
get the polisher wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT
allow untrained persons to operate the polisher.
8
DO NOT
operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT
leave the polisher operating unattended.
8
DO NOT
carry the polisher with your finger on the power switch.
8
DO NOT
pull the cord from the power supply.
9
Use a qualified person to maintain the polisher.
9
When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
2. INTRODUCTION
D
igital display and variable speed control from 2100-5000rpm. 15mm Orbit for greater polishing efficiency. Features a slide button on/off
switch allowing for a smooth comfortable main handle grip. Spindle lock for fast and easy pad changes. Double injection composite housing
with rubber grip for added comfort. Requires Model No’s CP20VBP, CP20VBP2 or CP20VBP4 20V Battery and Model No. CP20VMC Mains
Charger. Supplied with Ø125mm backing pad.
3. SPECIFICATION
Model No:..............................................................CP20VOP
Battery: .................................................
20V 2Ah - 6Ah Li-ion
Free Speed: ....................................................
2100-5000rpm
Noise Power/Pressure: ........................................
86/75dB(A)
Pad Size: ................................................................
Ø125mm
Vibration/Uncertainty: .........................................
4.56/1.5m/s²
C
P20VOP Issue 1 06/05/20
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear protective
clothing
Wear a mask
