8
do Not
insert foreign objects or material into the hole reserved for the battery.
8
do Not
force the battery into the charger. the battery will only fit one way to ensure correct polarity alignment.
8
do Not
charge a second battery immediately. consecutive charging will overheat the charger. Allow the unit to cool for 15 minutes
before charging the next battery.
9
store the charger in the same manner as the battery, see section 1.2.
1.3.
GeNeral Safety.
9
maintain the impact driver and battery in good condition. check moving parts alignment on a regular basis.
9
replace or repair damaged parts. use an authorised service agent and recommended parts only. unauthorised parts may be
dangerous and will invalidate the warranty.
9
ensure the impact driver is switched off before installing the battery pack.
9
Keep the impact driver and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Impact Driver; e.g. ceilings, floors and enclosures may contain electrical items or water
piping
9
ensure battery pack is correctly inserted into the impact driver handle and latched in place before attempting to switch on impact
driver.
9
secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this impact driver does not need to be plugged into the mains power.
9
Keep direction switch in the locked position until the impact driver is required for use.
9
Keep children and unauthorised persons away from the working area.
8
do Not
use the Impact Driver where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
do Not
allow children to operate the impact driver.
8
do Not
operate the impact driver if any parts are missing as this may cause failure and/or personal injury.
8
do Not
hold unsecured work piece in your hand.
8
do Not
leave the impact driver operating unattended.
8
do Not
carry the impact driver with your finger on the power switch. Keep chuck direction switch in the locked position.
8
do Not
use the impact driver for a task it is not designed to perform.
8
do Not
operate the impact driver when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do Not
get the impact driver or battery charger wet or use in damp or wet locations.
2. iNtroductioN
compact, lightweight cordless impact driver. comfortable composite housing with soft grip to reduce vibration. Variable speed control trigger
with lock fuction (in off position) gives more control during application. integrated led battery level indicator and led work light, and belt
hook. requires model no.cP1200BP 12V 1.5Ah lithium-ion battery and model no. cP1200mc battery charger.
3. SpecificatioN
model no.. ................................................................. cP1203
Battery .................................. 12V 1.5Ah li-ion (not included)
drive ........................................................................1/4” Hex.
impact rate ........................................................... 0-3500bpm
no load speed ......................................................0-2500rpm
maximum torque .............................................. 80nm(58lb.ft)
Battery model no ..................................................cP1200BP
mains charger model no .....................................cP1200mc
Weight ......................................................................... 0.80kg
4. cHArging
4.1.
battery pack removal and replacement
4.1.1.
switch the machine off before removing the battery pack.
4.1.2.
Press the battery latches in (located either side of grip
and withdraw the battery pack (fig.1).
4.1.3.
to replace the battery pack, push the stem into the drill
until the latches engage. the battery pack can only be
inserted in the correct orientation.
4.2.
battery charging
4.2.1.
Batteries that have been out of use for some time or are new
may not accept a full charge. this is not a battery fault; the
battery may need to be discharged and charged a couple of
times to restore full capacity.
4.2.2.
Connect the charger to the electric power supply. A flashing
green led will show.
4.2.3.
insert the battery into the charger. A steady red light
will show.
4.2.4.
When fully charged, a steady green led will show.
4.2.5.
the battery is ready for use.
fig.1
cP1203 | issue 1 26/09/16
Original Language Version
© Jack sealey limited