3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BT01
Rated Battery Voltage:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
Test Ranges: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-670 CCA* DIN
90-1125 CCA* EN
65-790 CCA* IEC
120-1440 CCA* MCA
100-1200 CCA* SAE
Voltage Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15V
Minimum Power Requirement: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Note: *CCA - Cold Cranking Amps
BT01 Issue:1 - 12/07/17
Original Language Version
© Jack Sealey Limited
4.1.
BATTERY TEST
4.1.1. Before testing a battery in a vehicle: turn off the ignition, all electrical
accessories and loads. Close all vehicle doors and the boot lid/tailgate.
4.1.2. Ensure that the battery terminals are clean; wire brush them if necessary.
4.1.3. Clamp the black battery tester lead to the negative (-) battery terminal.
4.1.4. Clamp the red battery tester lead to the positive (+) battery terminal.
4.1.5. The LED display will light and show the voltage of the battery on the screen.
Press ‘ENTER’ to proceed to the next step.
NOTE:
If the screen shows
HI
/
Lo
/
----
/
blank
or the screen flickers, refer to
troubleshooting (section 5.).
4.1.6. Press
/▼ key to select battery type:
SLI
: Standard SLI (
S
tarting,
L
ighting,
I
gnition) flooded batteries.
VRLA
: VRLA (
V
alve
R
egulated
L
ead
A
cid)/GEL/MF (
M
aintenance
F
ree)
batteries.
FLAt
: AGM (
A
bsorbed
G
lass
M
at) flat plate.
SPL:
AGM spiral battery.
4.1.7. Press ‘ENTER
4. OPERATION
4.1.8. Press
/▼ key to input the battery capacity of CCA or CA (MCA):
SAE, din, IEC, En
or
CA
(MCA).
4.1.9. Press ▲/▼ key to input the battery capacity of CCA or CA(MCA):
SAE : 100~1200,CCA∙DIN : 55~670, CCA∙IEC: 65~790,CCA∙EN: 90~1125,CCA∙CA(MCA) : 120~1440
4.1.10. Press “ENTER” to begin the test.
4.1.11. Test the battery within 1 second.
4.1.12. If the display shows
CHA-
(Is tested battery charged?). Please press “ENTER” & select ▲\▼ key to choose
yES
or
no
, then press
“ENTER” to the next step.
4.1.13. When the test is complete, the LED display shows the actual CCA. One of following five results will be displayed by the LED lamps:
Green LED light
The battery is good & capable of holding a charge.
XXXX (CCA value) SAE
Green & Yellow LED lights
The battery is good but needs to be charged.
XXXX (CCA value) SAE
Yellow & Red LED lights
Battery is discharged. The battery condition cannot be determined until it is fully charged.
Recharge & retest the battery. If reading is the same, the battery should be replaced
immediately.
XXXX (CCA value) SAE
Red LED light
-The battery cannot hold a charge. It should be replaced immediately. Or:
- The battery has at least one cell short circuit .It should be replaced immediately.
XXXX (CCA value) SAE
Err on the screen & Second Red light
– The clamps are not connected properly. Check if the clamps are connected properly. Or:
– The tested battery is bigger than maximum testing CCA capacity.
