background image

INSTRUCTIONS FOR:

WORKSHOP CYCLE STAND

MODEL No: 

BS103

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions 

give complete satisfaction.

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, 

WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. 

FAILURE TO DO SO MAY CAUSE DAMAGE OR  SERIOUS PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. 

PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

       Maintain the stand in good condition, replace or repair damaged parts. Use recommended parts only. Non authorised parts may be  

 

dangerous and will invalidate the warranty.

 

Before use ensure that all stand nuts, bolts and clamps are tight and that moveable and clamping parts are in good working order.

 

Place stand on a sound, level surface offering adequate working clearance for its function. 

 

Keep area clean, tidy and free from unrelated materials. Ensure there is adequate lighting.

 

Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.

 

Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.

 

Keep children, pets and unauthorised persons away from the working area.

DO NOT 

use the stand for any purpose other than for which it is designed.

DO NOT 

get the stand wet or use in damp or wet locations or areas where there is condensation. 

 

 

When not in use, store the stand in a safe, dry, child proof area. 

 

Avoid damage to the bicycle frame and cables etc. when tightening clamps.

7

 

DO NOT

 exceed the maximum load of 

30kg

.

NOTE:

 This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of 

 

experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person 

 

responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

1.  SAFETY INSTRUCTIONS

2. INTRODUCTION 

Heavy-duty cycle stand with adjustable work height. Ideal for home and workshop use. Fitted with articulated rubber coated frame clamp preventing 

damage to paintwork. Features four folding legs with a 1370mm span for added stability and multi-position tool tray to ensure tools are always close 

to hand. Adjustable cycle locking strap to prevent wheel movement available separately - order Model No. BS102S (see fig.3).

3. SPECIFICATION

4.  ASSEMBLY / OPERATION

Model No: .........................................................BS103

Minimum Working Height: .............................1050mm

Maximum Working Height: ............................1750mm 

Weight: ...............................................................

6.2kg

Maximum Load: ...................................................30kg

Cycle Frame Sizes: ............................35mm to 65mm

4.1. 

Unpack the contents, should there be anything damaged or missing contact  

 

your supplier.

4.1.1.  Release the quick release clamp (1) hold the tube (A) and push down on the  

 

clamp so that the legs spread out fully. Tighten the quick release clamp. The  

 

legs can be spread out less wide, but this may compromise the stability of the  

 

stand, depending on the position/weight of the cycle when mounted on the  

 stand.

4.1.2.  Ensure the four feet (2) are placed flat on the floor surface, which should be  

 

stable and level. The stand can be permanently fixed to the floor if required.

4.1.3.  Insert the telescopic shaft (B) into tube (A) and lock into place.

4.1.4.  Attach the bike support clamp head (C) onto the telescopic bar.

4.1.5.  Attach the tool storage tray (D) to the tube (A) and tighten the two hex. bolts.

4.1.6.  Check all fixings for stability and adjust and/or re-tighten them if necessary.

4.1.7.  Lift a cycle onto the stand, making sure that it is mounted centrally for 

 

maximum stability and to avoid straining the clamp.

4.1.8.  Secure it on the stand by positioning the top frame tube into the clamp and  

 

tightening it using the quick release clamp (fig.2).

4.1.9.  To adjust the angle of the cycle, it is advisable to remove the cycle from the  

 

stand and to make the required adjustments. If adjusting with the cycle still  

 

mounted on the stand, it is recommended that two people are utilised.  

 

 

Release the adjustment clamp just enough so that the cycle can be moved  

 

to the required angle and then re-tighten the clamp. 

4.1.10. To hold the front wheel in the correct position, use BS102S (fig.3).

4.1.11. Do not exceed the maximum extension height of shaft (B), there is a mark on  

 

the shaft. 

4.1.12. Always ensure that after repositioning the cycle on the stand, that the stand/ 

 

cycle are stable before carrying out any work.

4.1.13. After use, clean the stand, if required, with warm water and then dry with a  

 

clean cloth. Store the stand in a safe, dry, child proof location. 

©  Jack Sealey Ltd

Original Language Version 

BS103

     

Issue: 1 - 12/03/13

Fig.1

Reviews: