instructions for
BENCH GRINDER Ø150MM/Ø200MM
VARIABLE SPEED
model no:
BG150WVS & BG200WVS
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAfETy
1.1.
ELECTRICAL SAfETy
WARNING!
it is the user’s responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the bench grinder is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable
Appliance test) tested.
9
electrical safety information, it is important that the following information is read and understood.
9
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. ensure that any faulty item is
repaired or
replaced immediately by a qualified electrician.
9
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
9
if the cable or plug is damaged during use, switch the electricity supply off and remove from
use.
9
Ensure that repairs are carried out by a qualified electrician.
9
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified
electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
9
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is
tight.
9
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAfETy
WARNING! Disconnect the grinder from the mains power, and ensure the grinding wheels
are at a standstill before attempting to change accessories, service or perform any maintenance.
9
maintain the grinder in good condition and check moving parts alignment regularly.
9
replace or repair damaged parts. use recommended parts only. non-authorised parts may be dangerous and will invalidate the
warranty.
▲
DANGER
!
DO NOT
use a damaged wheel as it is dangerous and may cause damage and/or serious personal injury.
WARNING!
Only persons qualified under the “Abrasive Wheels Regulations” and holding a current grinding wheel certificate are to
change
or dress grinding wheels. Unplug grinder from mains power and refer to Section 4 “Grinding Wheels” for details.
WARNING!
Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.
A guard or any other part that is damaged should be repaired or replaced before tool is next used. the eye shields are a mandatory
fitting when grinder is used in premises covered by the Health & Safety at Work Act.
locate grinder in a suitable working area, keep area clean, tidy and free from unrelated materials. ensure adequate lighting.
9
Before each use check grinding wheels for condition. If worn or damaged replace immediately.
WARNING!
Always wear approved eye or face protection when operating the grinder.
9
Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard. Wear ear defenders.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the working area.
▲
DO NOT
use the grinder for a task it is not designed to perform.
8
DO NOT
operate the grinder if any parts are damaged or missing as this may cause failure and/or personal injury.
BG150WVS,BG200WVS | Issue 2 28/10/16
Original Language Version
© Jack sealey limited
refer to
instructions
Wear eye
protection
Wear ear
protection
Wear a protec
-
tive mask
recommended fuse rating
BG150WVS 5A
BG200WVS 13A
