© Jack Sealey Limited
Original Language Version
2. INTRODUCTION
Heavy-duty axle stands to safely support vehicle for extended periods of time. Heavy gauge steel frame and welded construction give superior
strength and safety. Large crutch for even load distribution. Features captive, multi-position pin load support. Ideal for commercial and public
service vehicles. Sold in pairs.
3. SPECIFICATION
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AS10
Capacity Each: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Tonne
Capacity Pair: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Tonne
Minimum Working Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573mm
Maximum Working Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775mm
4. OPERATION
4.1.
Refer to vehicle handbook for correct jacking procedure. Check to ensure manufacturer’s recommended jacking points are in good
condition.
4.2.
Position stands under recommended support points.
4.3.
To adjust stands, lift column up to jacking point, lower until next pin hole is visible, push pin all the way through it.
4.4.
Carefully and slowly lower vehicle onto stands. Ensure load bearing points sit in the centre of the crutches and that the stands are stable.
Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle onto the stands.
▲
DANGER!
You must follow instructions carefully and ensure you
DO NOT
load the stands off centre. Failure to heed these warnings may
cause damage, injury or loss of life.
5. MAINTENANCE
5.1.
Before each use, check that stands and stand welds are not cracked and that there are no missing or damaged parts. Any suspect axle
stands must be removed from service immediately.
5.2.
Owing to the potential hazards associated with stands do not misuse, or make any modification, to the stands or components.
5.3.
It is the responsibility of the owner to ensure that the operator has read these instructions together with the safety features on the side of
the stand and that the operator is familiar with its use and limitations.
AS10 Issue: 4 (3) 24/08/22
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
www.sealey.co.uk
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Parts support is available for this product. Please email [email protected] or telephone 01284 757500
