AK462DX.V2 Issue no: 3 - 21/08/17
Original Language Version
© Jack Sealey Limited
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to instruction
manual
Wear eye
protection
Wear protective
gloves
Wear protective
clothing
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
INSTRUCTIONS FOR:
GRAVITY & SUCTION FEED AIR
DISCHARGE CANTILEVER OIL DRAINER
Model No:
AK462DX.V2
1.1.
GENERAL SAFETY
WARNING
: Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
Familiarise yourself with the application and limitations of the oil drainer, as well as the potential hazards.
WARNING
: Disconnect the drainer from the air supply before changing accessories, servicing or performing any maintenance.
Maintain the drainer in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep the drainer clean for best and safest performance.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the working area.
WARNING
: ensure correct air pressure is maintained and not exceeded.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are
secure.
DO NOT
use the drainer for any purpose other than that for which it is designed.
DO NOT
operate the drainer if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT
stand on the drainer.
DO NOT
adjust or tamper with the safety valve.
DO NOT
move the drainer by the hose, or pull the hose sharply from the air supply.
DO NOT
place attachments close to your face and do not point hose at other persons or animals.
DO NOT
allow untrained persons to operate the drainer.
DO NOT
operate the drainer when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT
leave the drainer operating unattended.
DO NOT
direct air from the air hose at yourself or others.
When not in use disconnect from the air supply, vent reservoir and store in a safe, dry, childproof area.
Dispose of waste oil in accordance with local authority regulations.
WARNING: DO NOT
pollute the environment by allowing uncontrolled discharge of waste oil.
Steel fabricated 100ltr reservoir with suction probes and air discharge. Unit features cantilever oil drain pan which is suitable for use either under
a lift or on the forecourt. Drain pan utilises vacuum suction when in the down position and is fitted with castors for easy manoeuvring. Fitted with
oil level indicator tube and supplied with Mercedes adaptor plus a selection of probes.
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AK462DX
Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100ltr
Minimum Height to Pan: . . . . . . . . . . . . . . . . . . . . . . .130mm
Maximum Height to Pan: . . . . . . . . . . . . . . . . . . . . . .1660mm
Gravity Feed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes
Suction Feed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes
Gravity Discharge: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
Air Discharge: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes
Note: Numbers in brackets refer to item numbers on the Parts Diagram
4.1.
Remove the bolt, washer and nut (48, 49 & 50) from the support bar (82).
4.2.
Move the support bar (82) to the vertical position and engage the locking pivot bar (78) into the guide on the side of the reservoir.
4.3.
Align the holes in the support bar (82) and the bracket on the oil pan (42), fit the bolt (48) and secure using the washer and nut (49 & 50).
4.4.
Loosen the handle retaining bolts at the back of the reservoir, insert the handle and tighten the bolts.
4.5.
The oil drainer is now ready for use.
4. ASSEMBLY
