4.1.
Fit the handle assembly into the handle socket with the valve control lever towards the jack. Retain with the handle fixing
bolt. See fig.1.
4.2.
Before using the jack for the first time, purge the hydraulic circuit in order to eliminate any air in the system. To do this, open
the release valve by moving the lever downwards from position A to position B as shown in fig.2. In the lower position B the handle
must engage with one of the 3 handle locations indicated in fig.1. Once engaged the release valve can be opened by rotating the
lever fully sideways as shown in fig.2-C. Pump the foot pedal through its full travel 3 or 4 times. Return the release valve lever to
the upper closed position (see fig.2-A)
Model: . . . . . . . . . . . . . . . . . . . 10QJ.V2
Capacity:. . . . . . . . . . . . . . . . . . 10tonne
Min. Saddle Height: . . . . . . . . . . 160mm
Max. Saddle Height:. . . . . . . . . . 560mm
Max. Chassis Height: . . . . . . . 250mm
Length:… . . . . . . . . . . . . . . . . . 1637mm
Weight: . . . . . . . . . . . . . . . . . . . . . 129kg
3
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
3
Locate the jack in a suitable, well lit work area.
3
Keep work area clean and tidy and free from unrelated materials.
3
Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
3
Place wedges under wheels of vehicle (but ensure wheels of jack can move freely).
3
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in 1st or reverse gear (“PARK” if automatic).
3
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
3
Ensure there are no passengers in the vehicle.
3
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
3
Only place jack under those lifting points recommended by vehicle manufacturer (see vehicle handbook).
3
Check the lifting point is stable and centred on the jack saddle.
3
Ensure the jack wheels are free to move and that there are no obstructions.
p
DANGER:
Use the jack for lifting only,
NOT
for supporting the lifted load.
3
Use suitable capacity axle stands under the vehicle before proceeding with any task.
3
Ensure there are no persons or obstructions beneath the vehicle before lowering.
3
Use a qualified person to maintain or repair the jack hydraulic system.
7
DO NOT
operate the jack if damaged.
7
DO NOT
allow untrained persons to operate the jack.
7
DO NOT
exceed the rated capacity of the jack.
7
DO NOT
allow the vehicle to move while supported by the jack, nor use the jack to move the vehicle.
7
DO NOT
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substance.
7
DO NOT
work under the vehicle until axle stands have been correctly positioned.
7
DO NOT
use the jack for purposes other than that for which it is designed.
7
DO NOT
top up hydraulic system with brake fluid. Use hydraulic jack oil only.
7
DO NOT
adjust the safety overload valve.
3
When not in use store jack, fully lowered, in a safe, dry, childproof area.
fig.1
INSTRUCTIONS FOR:
TROLLEY JACK 10TONNE LONG REACH
MODEL NO:
10QJ.V3
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
4. ASSEMBLY
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
Refer to
instruction
manual
Heavy-duty chassis with one-piece hydraulic unit. Handle mounted safety release prevents inadvertent lowering of load. Includes large diameter
saddle for easier positioning under the jacking point. Foot operated quick lift system. Fitted with safety overload valve. Fully CE approved for
general workshop applications.
Original Language Version
10QJ.V3 Issue: 1 - 11/11/14
© Jack Sealey Limited
