manualshive.com logo in svg

SeaLevel DUAL SIO 3082, User Manual, Page: 12 / 21

Share
Download
SeaLevel DUAL SIO 3082 User Manual Download Page 12

 

Specifications 

Sealevel Systems 

Dual SIO

 

Page 

8

 

Specifications 

Environmental Specifications 

 

Specification 

Operating 

Storage 

Temperature Range 

0º to 50º C  

(32º to 122º F ) 

-20º to 70º C  

(-4º to 158º F) 

Humidity Range 

10 to 90% R.H. 

Non-Condensing 

10 to 90% R.H. 

Non-Condensing 

 

 

Manufacturing  

• 

All Sealevel Systems Printed Circuit boards are built to U.L. 94V0 
rating and are 100% electrically tested. These printed circuit boards 
are solder mask over bare copper or solder mask over tin nickel.  

Power Consumption 

 

Supply line 

+12 VDC  -12 VDC  +5 VDC 

Rating 

25 mA 

25 mA 

195 mA 

 

Mean Time Between Failures (MTBF) 

Greater than 150,000 hours. (Calculated) 
 

Physical Dimensions 

Board Length  

4.6 inches 

(11.68 cm) 

Board Height including Goldfingers 

4.2 inches 

(10.66 cm) 

Board Height excluding Goldfingers 

3.9 inches 

(9.906 cm) 

 

See Appendix E for board layout and dimensions. 

 

Summary of Contents for DUAL SIO 3082






















Reviews:

No comments