SeaLevel 7402e User Manual Download Page 21

 

21 

© Sealevel Systems, Inc.  7402e Manual   |   SL9251  11/2022 

Warranty 

Sealevel's commitment to providing the best I/O solutions is reflected in the Lifetime Warranty that is 
standard on all Sealevel manufactured I/O products. We are able to offer this warranty due to our control 
of manufacturing quality and the historically high reliability of our products in the field. Sealevel products 
are designed and manufactured at its Liberty, South Carolina facility, allowing direct control over product 
development, production, burn-in and testing. Sealevel achieved ISO-9001:2015 certification in 2018. 

Warranty Policy 

Sealevel Systems, Inc. (hereafter "Sealevel") warrants that the Product shall conform to and perform in 
accordance with published technical specifications and shall be free of defects in materials and 
workmanship for the warranty period. In the event of failure, Sealevel will repair or replace the product at 
Sealevel's sole discretion. Failures resulting from misapplication or misuse of the Product, failure to adhere 
to any specifications or instructions, or failure resulting from neglect, abuse, accidents, or acts of nature 
are not covered under this warranty.  

Warranty service may be obtained by delivering the Product to Sealevel and providing proof of purchase. 
Customer agrees to ensure the Product or assume the risk of loss or damage in transit, to prepay shipping 
charges to Sealevel, and to use the original shipping container or equivalent. Warranty is valid only for 
original purchaser and is not transferable.  

This warranty applies to  Sealevel manufactured Product. Product purchased through Sealevel but 
manufactured by a third party will retain the original manufacturer's warranty.  

Non-Warranty Repair/Retest

 

Products returned due to damage or misuse and Products retested with no problem found are subject to 
repair/retest charges. A purchase order or credit card number and authorization must be provided in order 
to obtain an RMA (Return Merchandise Authorization) number prior to returning Product.  

How to obtain an RMA (Return Merchandise Authorization) 

If you need to return a product for warranty or non-warranty repair, you must first obtain an RMA number. 
Please contact Sealevel Systems, Inc. Technical Support for assistance: 

Available  

Monday – Friday, 8:00AM to 5:00PM EST 

Phone   

864-843-4343  

Email 

 

[email protected]

 

Trademarks 

Sealevel Systems, Incorporated acknowledges that all trademarks referenced in this manual are the service 
mark, trademark, or registered trademark of the respective company.  

Summary of Contents for 7402e






















Reviews: