Seagull Models MAXI LIFT 33cc Assembly Manual Download Page 1 | Manualshive

Page: 1 / 27

background image

WWW.SEAGULLMODELS.COM

1

ASSEMBLY MANUAL

MS: 209

www.seagullmodels.com

MAXI LIFT

“ Graphics and specifications may change without notice “ .

Specifications:

Wingspan---------------87.6 in (222.2 cm).
Wing area----------------1072.6sq.in (69.2 sq.dm).
Weight-------------------11.5 - 12.1 lbs (5.2 - 5.5 kg).
Length-------------------61.2 in (155.5cm).
Recommended engine size 33cc...............................
Radio--------------------7 channels with 10 servos.
Flying skill level intermediate/ advanced

ALMOST

READY TO FLY

33cc

1
2
3
...
»

Summary of Contents for MAXI LIFT 33cc




























Reviews:

No comments

Related manuals for MAXI LIFT 33cc

Brand: Harbor Freight Tools Pages: 7

Brand: Fisher-Price Pages: 6

Steaman Aerobatic Biplane

Brand: REVELL Pages: 12

Brand: F-One Pages: 20

Toot-Toot Drivers Press ‘n’ Go Vehicle

Brand: VTech Pages: 3

Monogram The Gold Knight Of Nice

Brand: REVELL Pages: 8

Mini Dual Deploy Screech

Brand: Madcow Rocketry Pages: 3

COFFEE CUPS ROUNDABOUTS

Brand: Faller Pages: 12

Brand: LEGO Pages: 59

Brand: Radio Shack Pages: 16

Brand: Trix Pages: 36

Brand: Beyblade Pages: 2

Brand: Faller Pages: 4

Brand: pitsco Pages: 162

Stuart Little Roadster

Brand: Radio Shack Pages: 8

SU27 FLANKER 60-91

Brand: Vmar Pages: 16

mini dual deploy DX3

Brand: Madcow Rocketry Pages: 3

Brand: LEGO Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands