manualshive.com logo in svg

Seagull Models EXTRA EA300L EP, Assembly Manual

Share
Download
Seagull Models EXTRA EA300L EP Assembly Manual Download Page 16

EXTRA EA300L EP

                              

                               Instruction Manual.

16

   Rudder pushrod

  Elevator pushrod

ELEVATOR - RUDDER  PUSHROD

HORN        INSTALLATION.

 

1) Install the elevator control horn using

the same method as with the aileron control
horns.

 

2) Position the elevator control horn on

the both side of elevator.

Elevator pushrod.

8mm

INSTALLATION PILOT.

1)  A scale pilot is included with this ARF. The
Seagull Pilot included fitting well to the cockpit.
(or you can order others scale pilot figures
made by Seagull factory. They are available at
Seagull distributors.)

If you are going to install a pilot figure, please
use a sanding bar to sand the base of the figure
so that it is flat.

2)  Position the pilot figure on the canopy floor
as show. Locate the oval shaped on the canopy
floor and remove the covering. Use epoxy to
glue this into the base of the pilot figure, please
see pictures as shown.

1

2

Nylon Snap Keeper

Nylon Snap Keeper

Pushrod Rudder

Fuel Tubing

Nylon Clevis

Fuel Tubing

Nylon Clevis

Pushrod Elevator

Summary of Contents for EXTRA EA300L EP




















Reviews:

No comments

Brands by name

Popular brands

Load more brands