Seagull Models CESSNA 188 AGWAGON Assembly Manual Download Page 1 | Manualshive

Page: 1 / 40

background image

1

Specifications:

Wingspan--------------- 97.2 in (246.8 cm).
Wing area--------------- 1110.4 sq.ins (71.6 sq.dm).
Weight------------------- 16.8 lbs (7.6 kg).
Length------------------- 59.7 in (151.7 cm).
Engine/Motor size----- 33cc gasoline.
Radio--------------------- 6 channels with 8 servos.

ASSEMBLY MANUAL

Code : SEA 299

1
2
3
...
»

Summary of Contents for CESSNA 188 AGWAGON









































Reviews:

No comments

Related manuals for CESSNA 188 AGWAGON

Brand: Kadee Pages: 2

Brand: Baby Einstein Pages: 6

Brand: K'Nex Pages: 30

Brand: K'Nex Pages: 44

40 MODEL BUILDING SET

Brand: K'Nex Pages: 13

Brand: K'Nex Education Pages: 35

Brand: K'Nex Pages: 2

Brand: K'Nex Education Pages: 24

100 MODEL IMAGINE BUILDING SET

Brand: K'Nex Pages: 78

100 MODEL IMAGINE BUILDING SET

Brand: K'Nex Pages: 64

Brand: T&J Pages: 11

Brand: PLAYTIVE JUNIOR Pages: 20

Star Wars 75004

Brand: LEGO Pages: 60

SMIT ROTTERDAM 478

Brand: Billing Boats Pages: 45

Brand: Spin Master Pages: 20

Val Tuoi Viaduct-Set

Brand: Faller Pages: 8

F-16C FIGHTING FALCON 1120mm 28/2021

Brand: Paper Replika Pages: 3

Super Honey Hawk

Brand: UberFly Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands