Seagull Models Boomerang 40 Assembly Manual Download Page 1 | Manualshive

Page: 1 / 22

Seagull Models Boomerang 40 Assembly Manual Download Page 1

Specifications

Wing span ____________________________  155cm.
Wing area _________________________ 3950 sq cm .
Approximate flying weight _______________  2.6-2.8kg.
Recommended  engine  size 0.40-0.46 cu. ins 2-stroke.
Recommended R/C __________ 4 channels minimum.
Flying skill level ___________________ Sports  Trainer.
Electric conversion: optional

Kit features.

•

Ready-made—minimal assembly & finishing required.

•

Ready-covered—including decals, trim & covering.

•

Factory-installed pushrod.

•

Factory-pinned & glued control surface hinges for ultimate safety.

•

Comprehensive hardware pack including wheels, tank, spats,undercarriage& spinner.

•

Photo-illustrated step-by-step Assembly Manual.

Hand-made Almost Ready to Fly R/C Model Aircraft

ASSEMBLY MANUAL

Additional items required.

Engine.
4 Channels or greater Radio Control system.
Glues.
Tools.
Starting Equipment.

Made in Vietnam.

SPORTS TRAINER - ENGINE SIZE.40 - .46 - 2STROKE

1
2
3
...
»

Summary of Contents for Boomerang 40























Reviews:

No comments