Seagull Models 15CC Assembly Manual Download Page 25 | Manualshive

Page: 25 / 34

background image

WWW.SEAGULLMODELS.COM

25

.

INSTALLATION PILOT AND CANOPY.

1) Locate items necessary to install pilot,

seats.

2) A scale pilot is included with this ARF.

The Seagull Pilot included fitting well to

the cockpit. (or you can order others scale

pilot figures made by Seagull factory.

They are available at Seagull distributors.)

If you are going to install a pilot figure,

please use a sanding bar to sand the base

of the figure so that it is flat.

Epoxy.

10mm

4) Position the canopy onto the fuselage.

Trace around the canopy and onto the

fuselage using a felt-tipped pen.

Epoxy.

3) Position the pilot figure on the cano-

py floor as shown. Use epoxy to glue the

base of the pilot figure, please see pic-

tures as shown.

«
...
23
24
25
26
27
...
»

Summary of Contents for 15CC



































Reviews:

No comments

Related manuals for 15CC

Brand: Bell Pages: 220

Brand: Team Losi Pages: 43

Brand: Team Losi Pages: 21

4-6-2 Pacific Steam Locomotive

Brand: Rail King Pages: 29

Brand: THUNDER TIGER Pages: 28

Poterie Professional POTTERY Studio

Brand: Buki Pages: 32

Ju 88C-6b Night Fighter exterior

Brand: Eduard Pages: 6

Brand: Playskool Pages: 2

GWR Meat Van Mica A/B NGSK0100

Brand: N Gauge Society Pages: 4

The Lone Ranger

Brand: Lionel Pages: 24

Lincoln Logs Big L Ranch

Brand: K'Nex Pages: 8

Zoom Ju 87A interior S.A.

Brand: Eduard Pages: 4

Brand: marklin Pages: 20

Discovery micro

Brand: m2model Pages: 3

Brand: JMB-Jets Pages: 15

Gravitrax LOOPING

Brand: Ravensburger Pages: 4

Brand: Hyperflight Pages: 12

Brand: The Drone Warehouse Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands