Seagate ST8000NE0001 Product Manual Download

Page: 22 / 32

Seagate Enterprise NAS HDD Product Manual, Rev. C

Configuring and mounting

3.4.1

Mechanical specifications

Refer to

Figure 4

for detailed mounting configuration dimensions. See Section

3.4

, “Drive mounting.”

Figure 4.

Mounting dimensions—top, side and end view (6TB)

Weight:

8TB & 6TB models

1.72 lb

780 g

Note

These dimensions conform to the Small Form Factor Standard documented
in SFF-8301 and SFF-8323, found at

www.sffcommittee.org

Note

The images below are for mechanical tolerance reference only
and may not be a visual representation of the actual drive.

3.750±.010

2X 1.625±.020 1.432 5

2X 3.000±.010

.127±.010

4.000±.010

2.000

.814 5

4X 6-32 UNC 2B

3 MIN THREAD DEPTH

.12 MAX FASTENER PENETRATION

MOUNTING HOLE.

MAX TORQUE 6 IN/LBS

5.787 MAX

146.99 MM

.250±.010

2X 4.000±.010

2X 1.122±.020

2X 6-32 UNC 2B

3 MIN THREAD DEPTH

.12 MAX FASTENER PENETRATION

MOUNTING HOLES BOTH SIDES.

MAX TORQUE 6 IN/LBS

1.028 MAX

26.11 MM

.138±.015 5

2.000

CL OF DRIVE

CL OF CONN

Summary of Contents for ST8000NE0001

































Search results

Summary of Contents for ST8000NE0001

Reviews:

Related manuals for ST8000NE0001

Brands by name

Popular brands

Seagate ST8000NE0001, Product Manual

Search results

Summary of Contents for ST8000NE0001

Reviews:

Related manuals for ST8000NE0001

Brands by name

Popular brands