S
EAGATE
L
APTOP
U
LTRATHIN
HDD SATA P
RODUCT
M
ANUAL
, R
EV
. C
12
D
RIVE
S
PECIFICATIONS
2.11
R
ELIABILITY
Nonrecoverable read errors
1 per 10
14
bits read, max
Load/Unload (U/UL)
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Warranty
To determine the warranty for a specific drive, use a web browser to access the
following web page::
http://www.seagate.com/support/warranty-and-replacements/
From this page, click on the “Verify Your Warranty” link. The following are required
to be provided: the drive serial number, model number (or part number) and country
of purchase. The system will display the warranty information for the drive.
2.12
A
GENCY
C
ERTIFICATION
2.12.1
Safety certification
These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency.
2.12.2
Electromagnetic Compatibility (EMC)
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility
Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product standards for
Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN
55024.
Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the
test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly
designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and
system integrators should confirm EMC compliance and provide CE marking for their products.
Korean RRL
If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the
Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the
Radio Research Laboratory (RRL) Communications Commission, Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B
products. Drives are tested in a representative, end-user system by a Korean-recognized lab.
Certificate number:
KCC-REM-STX-Ultrathin
Trade name or applicant:
Seagate Technology LLC
Certificate date:
2013-04-19
Manufacturer/nationality:
USA, Singapore and China
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548 1995 and meet the
Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA).
2.12.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As
such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal
Communications Commission verification or certification of the device is required.
Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard,
power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart
J, Part 15 of the FCC rules. Operation
with noncertified assemblies is likely to result in interference to radio and television reception.
Radio and television interference
This equipment generates and uses radio frequency energy and if not installed and used in strict
accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which
can be determined by turning the equipment on and off, it is recommended to try one or more of the following corrective measures:
