Seagate SV35 Series HDD Product Manual, Rev. E
5
www.seagate.com
*One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending
on operating environment and formatting.
* *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.
*** All specifications above are based on native configurations.
2.2
Formatted capacity
*One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending
on operating environment and formatting.
2.2.1
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to
n–1,
where
n
is
the number of guaranteed sectors as defined above
.
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit
addressing support of drives with capacities over 137GB.
Altitude, non-operating
(below mean sea level, max)
–304.8m to 12,192m
(–1000 ft to 40,000+ ft)
–304.8m to 12,192m
(–1000 ft to 40,000+ ft)
–304.8m to 12,192m
(–1000 ft to 40,000+ ft)
Operational Shock (max)
80 Gs at 2ms
80 Gs at 2ms
80 Gs at 2ms
Non-Operational Shock (max)
300 Gs at 2ms
300 Gs at 2ms
350 Gs at 2ms
Vibration, operating
2Hz to 22Hz: 0.25 Gs
(Limited displacement)
22Hz to 350Hz: 0.50 Gs
350Hz to 500Hz: 0.25 Gs
2Hz to 22Hz: 0.25 Gs
(Limited displacement)
22Hz to 350Hz: 0.50 Gs
350Hz to 500Hz: 0.25 Gs
2Hz to 22Hz: 0.25 Gs
(Limited displacement)
22Hz to 350Hz: 0.50 Gs
350Hz to 500Hz: 0.25 Gs
Vibration, non-operating
5Hz to 22Hz: 3.0 Gs
22Hz to 350Hz: 3.0 Gs
350Hz to 500Hz: 3.0 Gs
5Hz to 22Hz: 3.0 Gs
22Hz to 350Hz: 3.0 Gs
350Hz to 500Hz: 3.0 Gs
5Hz to 22Hz: 3.0 Gs
22Hz to 350Hz: 3.0 Gs
350Hz to 500Hz: 3.0 Gs
Drive acoustics, sound power
Idle**
2.4 bels (typical)
2.6 bels (max)
2.4 bels (typical)
2.6 bels (max)
2.2 bels (typical)
2.3 bels (max)
Seek
2.6 bels (typical)
2.7 bels (max)
2.6 bels (typical)
2.7 bels (max)
2.3 bels (typical)
2.4 bels (max)
Non-recoverable read errors
1 per 10
14
bits read
1 per 10
14
bits read
1 per 10
14
bits read
Annualized Failure Rate (AFR)
<1%
<1%
<1%
Warranty
To determine the warranty for a specific drive, use a web browser to access the following web page:
http://www.seagate.com/support/warranty-and-replacements/
.
From this page, click on the “Check to see if the drive is under Warranty” link. The following are required to be
provided: the drive serial number, model number (or part number) and country of purchase. The system will
display the warranty information for the drive.
Load/Unload cycles
(25°C, 50% rel. humidity)
300,000
300,000
300,000
Supports Hotplug operation per the
Serial ATA Revision 3.2 specification
Yes
Yes
Yes
Model
Formatted
capacity*
Guaranteed
sectors
Bytes per sector
ST3000VX000
3000GB
5,860,533,168
4K
ST2000VX000
2000GB
3,907,029,168
ST1000VX000
1000GB
1,953,525,168
Table 1
Drive specifications summary for 3TB, 2TB and 1TB models (Continued)
Drive Specification
ST3000VX000
ST2000VX000
ST1000VX000
