background image

2

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

1.2

About Momentus 7200 FDE.1 SATA disc drives

Momentus

®

 7200 FDE.1 SATA drives contain DriveTrust technology providing Full Disc Encryption (FDE) 

using proven Advanced Encryption Standard (AES) data encryption and decryption.

You can elect to use Momentus 7200 FDE.1 SATA drives in one of two different security modes:

1.

The ATA Security mode

To operate in ATA Security mode, you only need a host system and operating system that supports the 
existing ATA Security Command Set. The drive is shipped to operating in this mode, ready to use.

2.

The DriveTrust Security mode

To enable a robust enterprise-level security and management policy, you may elect to operate in 
DriveTrust Security mode. To do so, you will need to use a third-party security application to manage the 
DriveTrust features. Please contact your system or software provider for more details.

Refer to the table below to determine which mode is best for your particular solution. 

FDE drive feature list

• Automatically encrypts (and decrypts) all data on the drive

• Operations are performed with no measurable performance loss

• All user data is encrypted on write operations and decrypted on read operations

FDE benefits

• Drive-level protection of data

• Drives that are stolen, taken out of service, or re-purposed remain fully protected

• Near instantaneous disposal and re-purposing of the drive (ensures that data from previous user is not 

accessible by the new drive owner)

• Able to be deployed within a trusted computing environment

The drive encrypts every write operation and decrypts every read operation without user intervention. The 
encryption and decryption is done on the drive itself, so there is a near-zero performance impact when the 
drive writes and reads data. The performance-optimized encryption and decryption engine performs at the 
SATA interface speed.

The purpose of full disc encryption on the drive is to protect the data stored on the drive in the event that the 
host system is lost or stolen. This data at rest protection assures the system owner that if their system is lost or 
stolen, their data will not be accessible without the correct credentials.

Note.

The system reauthenticates the user on powerup and when awakening from sleep mode. It is not 
necessary to power down to ensure that the system reauthenticates the user.

Table 1: 

Security feature matrix

ATA Security mode

DriveTrust mode

Feature

Non-FDE drive 
without ATA Security 
enabled

Non-FDE drive with 
ATA Security enabled

FDE drive with ATA 
Security enabled

FDE drive operating in 
DriveTrust mode via 
third-party software

Password required to unlock

No

Yes

Yes

Yes

Full Disk Encryption

No

No

Yes

Yes

At speed encryption

No

No

Yes

Yes

Passwords stored securely

No

Yes

Yes

Yes

Quick erase

No

No

Yes

Yes

Preboot authentication

No

No

No

Yes

Master/User passwords

No

No

No

Yes

Summary of Contents for Momentus 7200 FDE.1 SATA

































































Reviews: