Seagate Cheetah NS 10K Product Manual Download Page 55

Page: 55 / 90

Cheetah NS FC Product Manual, Rev. A

9.0

Interface requirements

This section partially describes the interface requirements as implemented on Cheetah NS FC drives. Addi-
tional information is provided in the Fibre Channel Interface Manual (part number 100293070).

9.1

FC-AL features

This section lists the Fibre Channel-specific features supported by Cheetah NS FC drives.

9.1.1

Fibre Channel link service frames

Table 5 lists the link services supported by Cheetah NS FC drives.

Table 5:

Link services supported

Type of frame

Link service

Basic link service frames

Abort Sequence (ABTS)

Basic link service reply frames

Basic_Accept (BA_ACC)

Basic_Reject (BA_RJT)

Extended link service frames

N_Port Login (PLOGI)

Fabric Login (FLOGI)

Logout (LOGO)

Process Login (PRLI)

Process Logout (PRLO)

Read Link Status (RLS)

Fabric Address Notification (FAN)

Port Discovery (PDISC)

Address Discovery (ADISC)

Third-party Process Logout (TRPLO)

Extended link service reply frames

Accept (ACC)

Link Service Reject (LS_RJT)

Fibre Channel Services

Summary of Contents for Cheetah NS 10K



























































































Search results

Summary of Contents for Cheetah NS 10K

Reviews:

Related manuals for Cheetah NS 10K

Brands by name

Popular brands

Seagate Cheetah NS 10K, Product Manual

Search results

Summary of Contents for Cheetah NS 10K

Reviews:

Related manuals for Cheetah NS 10K

Brands by name

Popular brands