Seagate Barracuda ES.2 FC Product Manual Download Page 13

Page: 13 / 84

Barracuda ES.2 FC Product Manual, Rev. B

2.3

Reference documents

SCSI Commands Reference Manual

Seagate part number: 100293068

Fibre Channel Interface Manual

Seagate part number: 100293070

ANSI Fibre Channel Documents

X3.230-1994

FC Physical and Signaling Interface (FC-PH)

X3.297.1997

FC-PH-2 Fibre Channel Physical and Signaling Interface-2

X3.303.1998

FC-PH-3 Fibre Channel Physical and Signaling Interface-3

X3.272-1996

FC Arbitrated Loop (FC-AL)

X3.269-1996

Fibre Channel Protocol for SCSI (FCP)

NCITS TR-19

Private Loop SCSI Direct Attach (PLDA)

NCITS TR-20

Fabric Loop Attachment (FC-FLA)

SFF-8045

Specification for 40-pin SCA-2 Connector with Parallel Selection

SFF-8067

Specification for 40-pin SCA-2 Connector with Bidirectional

Enclosure Services Interface

ANSI Small Computer System Interface (SCSI) Documents

X3.131-1994

(SCSI-2)

X3.270-1996

(SCSI-3) Architecture Model

NCITS 305-199X

(SCSI-3) Enclosure Services

Specification for Acoustic Test Requirement and Procedures

Seagate part number: 30553-001

Package Test Specification

Seagate P/N 30190-001 (under 100 lb.)

Package Test Specification

Seagate P/N 30191-001 (over 100 lb.)

In case of conflict between this document and any referenced document, this document takes precedence.

Summary of Contents for Barracuda ES.2 FC





















































































Search results

Summary of Contents for Barracuda ES.2 FC

Reviews:

Related manuals for Barracuda ES.2 FC

Brands by name

Popular brands

Seagate Barracuda ES.2 FC, Product Manual

Search results

Summary of Contents for Barracuda ES.2 FC

Reviews:

Related manuals for Barracuda ES.2 FC

Brands by name

Popular brands