Seagate 600 Pro SSD, Product Manual

Page: 7 / 41

S
EAGATE
600 P
RO
SSD P
RODUCT
M
ANUAL
, R
EV
. A 3
2.0 D
RIVE SPECIFICATIONS
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For
convenience, the phrases
the drive and this drive are used throughout this manual to indicate the following drive models:
Product data communicated in this manual is specific only to the model numbers listed in this manual. The data listed in this
manual may not be predictive of future generation specifications or requirements. If you are designing a system which will
use one of the models listed or future generation products and need further assistance, please contact your Customer
Technical Support Engineer or our global support services group as shown in See “Seagate Technology Support Services”
on page
1.
2.1 S
PECIFICATION SUMMARY TABLES
The specifications listed in the following table is for quick reference. For details on specification measurement or definition,
see the appropriate section of this manual.
Table 1 Drive specifications summary for 2.5” - 400, 200 and 100 GB models
Capacity
480GB 400Gb 240GB 200GB 120GB 100GB
2.5” Managed Life Warranty
ST480FN0001 ST400FN0001 ST240FN0001 ST200FN0001 ST120FN0001 ST100FN0001
2.5” Usage Based Warranty
ST480FN0021 ST400FN0021 ST240FN0021 ST200FN0021 ST120FN0021 ST100FN0021
Drive specification
ST480FN0001
ST480FN0021 ST400FN0001
ST400FN0021 ST240FN0001
ST240FN0021 ST200FN0001
ST200FN0021 ST120FN0001
ST120FN0021 ST100FN0001
ST100FN0021
Formatted GB (512 bytes/sector)
[1]
480 400 240 200 120 100
Guaranteed logical block addresses (LBAs) 937,703,088 781,422,768 468,862,128 390,721,968 234,441,648 195,371,568
Emulated Bytes per LBA 512
Peak128KB sequential read/write data transfer rate
(MB/s max)
520/400 520/300
Sustained 128KB sequential read/write data transfer
rate
(MB/s max)
520/400 520/300
Peak 4KB Random read/write command rate
(KIOPs)
85/30 80/20
Sustained 4KB Random read/write command rate
(KIOPs)
85/11 85/30 85/11 85/30 80/8 80/20
Flash Memory Type NAND MLC
I/O data-transfer rate (MB/s max) 600
Height (mm max) 7.00 mm (0.276 in)
Width (mm max) 70.10 mm (2.760 in)
Length (mm max) 100.45 mm (3.955 in)
Weight (max) 100 g (0.220 lb)
Power-on to ready (sec typ)
[2]
3 sec
Standby to ready (sec max) 3 sec
Average LBA access time ( μ s typ) ~158 μ s read; ~125 μ s write
Data Retention (typical minimum at 40°C) 3 months
Sustainable Write Bandwidth under JEDEC Mix for
3 Year Endurance at 100% duty cycle in MB/sec
2.5 9.7 1.3 4.8 0.6 2.4
Startup current 5V (typical/peak) 550 / 600 mA
Voltage tolerance (including noise) 5V ± 5%
Temperature
0° to 70°C (operating as reported by SMART attribute 194)
–40° to 75°C (nonoperating)
Temperature gradient (°C per hour max)
20°C (operating)
20°C (nonoperating)
Relative humidity
5% to 95% (operating)
5% to 95% (nonoperating)
Relative humidity gradient 20% per hour max