SeaDoo Rotax 1503 4-Tec 2005 Page 53 Engine Shop Manual Download

Page: 53 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 04 (LUBRICATION SYSTEM)

GENERAL

For oil change procedure, refer to LUBRICATION
in the appropriate

VEHICLE SHOP MANUAL

PROCEDURES

ENGINE OIL PRESSURE

NOTE:

Depending the oil pressure switch, the

threshold value to send a signal of low oil pressure
may vary from a minimum of 180 kPa (26 PSI) to
a maximum of 220 kPa (32 PSI).

NOTE:

The engine pressure test should be done

with a warm engine and the recommended oil.

Use oil pressure gauge (P/N 529 035 709) and
hose adaptor (P/N 529 035 652) and install where
shown. A 1/8 NPT pipe extension may ease the
installation.

529 035 709

529 035 652

Test at the Oil Pressure Switch Location

Remove oil pressure switch and install gauge.

F18D2YA

INSTALLATION AT PRESSURE SWITCH LOCATION

1. Remove oil pressure switch and install gauge here

To prevent the EMS to go in limp home mode (at
2500 RPM) or to generate a fault code, start en-
gine, THEN ground OPS connector to engine.

Read oil pressure at different RPM as per follow-
ing table.

OIL PRESSURE

MEASURED AT PRESSURE

SWITCH LOCATION

1503 4-TEC NATURALLY ASPIRATED ENGINE

ENGINE RPM

PRESSURE kPa (PSI)

Idle (cold)

296 - 400 (43 - 58)

Idle (at 80°C (176°F)

Min. 160 (23)

4000 - 7500

296 - 400 (43 - 58)

ALL 1503 4-TEC SUPERCHARGED ENGINES

Idle (cold)

448 - 648 (65 - 94)

for a very short time

Idle (at 80°C (176°F)

Min. 228 (33)

4000 - 7500

400 - 496 (58 - 72)

Reinstall oil pressure switch.

Test at the Cylinder Head Location

The oil pressure may be measured from cylinder
head if desired.

Remove plug located on cylinder head and install
gauge.

SMR2005-035

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands