SeaDoo Rotax 1503 4-Tec 2005 Page 22 Engine Shop Manual Download

Page: 22 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 02 (INTAKE MANIFOLD AND SUPERCHARGER)

If the torque is not within specifications, repair
supercharger clutch. Verify supercharger clutch
components as per INSPECTION (PARTS DISAS-
SEMBLED) further in this section.

REMOVAL

Intake Manifold

NOTE:

Remove required parts to access intake

manifold. Refer to appropriate

VEHICLE SHOP

MANUAL

Remove oil dipstick.

Pull fuel rail cover out.

Release the fuel pressure in the system, refer to
ENGINE MANAGEMENT section of the appropri-
ate

VEHICLE SHOP MANUAL

Disconnect battery cables from battery.



WARNING

Always disconnect battery cables exactly in
the specified order, BLACK negative cable
first then the RED positive battery cable last.

Disconnect fuel hose connector at fuel rail.

R1503motr78A

Step 1: Squeeze
Step 2: Pull out
1. Supporting tabs
2. Squeeze in middle of supporting tabs, hold and pull out

Cut locking ties where shown.

F18D0CA

NATURALLY ASPIRATED ENGINE

1. Cut locking ties to release harness

R1503motr222A

SUPERCHARGED ENGINE

1. Cut locking ties to release harness

SMR2005-033

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands