background image

External Controls

E-18

Unauthorized disassembling and/or modification could 

result in malfunction or flooding, and void product warranty.  

Take the product to a SEA&SEA authorized service center 

for repair or inspection.

Never expose the battery to flame or fire, or to excessive heat.

Never attempt to disassemble, alter or directly solder the battery.

There are no user-serviceable parts.  Tampering with battery 

may expose you to dangerous voltage, battery acid, or 

electrical shock.

Never short-circuit the terminals of a battery, as it could result 

in battery leakage, heat generation, fire, or explosion.   Avoid 

contact with all metal objects during  transporting and storage.

Move leaking batteries away from fire or open flames 

immediately.  The leaked fluid and its vapor are combustible.

If the battery leakage contacts your skin or clothing, flush the 

affected area repeatedly with clean water.  It may irritate your 

skin.  Should it get into your eyes, immediately rinse them 

with plenty of water, avoid rubbing and seek medical advice.

Never attempt to insert the battery upside down or backward, 

as it could result in battery leakage or explosion.  Always 

confirm the direction of plus and minus before installation.

Never connect a battery directly to a plug outlet or car 

cigarette lighter.

Use only batteries approved for use in this product. Do not 

mix old and new batteries or batteries of different types.

Remove batteries before transport or storage, or when you 

are not going to use the product for an extended period of 

time, to prevent unexpected activation.

2

1

1

ON

OFF

ON

OFF

Set the power 

switch to ON.

1

Press the test light button to confirm that it 

lights up.

2

Set the power 

switch to OFF.

1

If the forked tip of the sensor section is wet, wipe 

it with dry cloth.

2

If it is not wiped off sufficiently, the LED lamp lights up 

when the power is switched on.

When the leak sensor is not to be used for long time, 

store it with the battery removed.

Make  sure  that  the  ends  of  the  forked  tip  of  the 

sensor section are not in contact with each other.

The  LED  lamp  lights  as  long  as  the  test  light 

button is pressed. If it does not light up, replace 

the battery with a new one.

If you will not use the product for an extended period of 

time,  store  it  away  from  high  temperatures,  high 

humidity, direct sunlight, or extreme cold.

Do not store the product with naphthalene or camphor 

mothballs,  or  in  locations  such  as  a  laboratory  where 

chemicals are used. This environment can cause mold, 

rust, corrosion or malfunction.

Always remove batteries from the product after use.

Set the battery

When inserting or replacing the battery, wipe off moisture on the leak sensor thoroughly and 

make sure that your fingers are dry. Take extra care for water droplets from your hair and wet 

suit. Otherwise, an electric shock, mold growth on the product, or malfunctioning may occur.

Using the Leak Sensor

Leak sensor

The leak sensor lights up in red when it detects leakage underwater. If it lights up, 

surface without delay while ensuring your safety and once out of water remove the 

camera from the housing.

Before use

After use

Maintenance and Storage

Keep dry.The battery is not waterproof, and may malfunction 

if immersed in water or exposed to high levels of humidity.  

Rusting of the internal mechanism can cause irreparable 

damage.

Do not remove and/or damage the case of a battery.  It may 

cause battery leakage, overheating or explosion.

Never use batteries should you notice any changes such as 

leakage, discoloration or deformation.  When you notice the 

situation as abnormal, discontinue use immediately and take the 

product to a SEA&SEA authorized service center for inspection.

Keep out of reach of children to prevent accidental ingestion.  

If swallowed, seek medical advice immediately.

Do not leave or use batteries in an extreme hot environment.  

This may cause battery leakage, overheating or battery 

performance deterioration.

Keep away from strong magnetic fields.  Do not use or store 

this product in the vicinity of equipment that generates strong 

electro-magnetic radiation or magnetic fields.  Strong static 

charges or the magnetic fields could cause malfunction, or 

affect the product's internal circuitry.

Avoid strong shocks/impacts or excess stress to batteries.

Dirt on the battery terminals can prevent the product from 

functioning.  Should the battery terminals become dirty, wipe 

them with a clean, dry cloth before use.

Turn the equipment off after use.  Remove batteries from the 

equipment when not in use.  Store in dry area with 

temperatures ranging from 0 to 30°C (32 to 86°F).

If LED lamp turn red due to malfunction, turn switch to OFF 

position and return back again to ON to resume normal operation.

DANGER 

WARNING 

CAUTION 

LED lamp will only light 

up  when  the  sensor  is 

wet.

Summary of Contents for MDX-D810





























Reviews: