Sea-doo 2000 Islandia Operator'S Manual Download Page 30

Page: 30 / 92

8) Docking Light Switch

A 2-position ON/OFF push type switch.

Lights may be operated without the
safety lanyard on its switch.

CAUTION:

Using the docking lights

for a prolonged time when the en-
gine is not running will discharge
the battery.

9) Boarding Light Switch

A 2-position ON/OFF push type switch.

Lights may be operated without the
safety lanyard on its switch.

CAUTION:

Using the boarding lights

for a prolonged time when the en-
gine is not running will discharge
the battery.

10) Engine Compartment

Light Switch

A 2-position ON/OFF push type switch.

11) Bilge Pump Switch

A 2-position ON/OFF push type switch.

Press switch to ON position when a
manual operation is required (after
cleaning, storage, etc.).

Press to OFF position when bilge is
dry.

CAUTION:

Using the bilge pump for

a prolonged time when the engine is
not running will discharge the bat-
tery.

NOTE:

The bilge pump may be operat-

ed without the safety lanyard on its
switch.

F00H1EY

F00H1FY

F00H1GY

F00H1HY

lmo2000-003a.book Page 28 Tuesday, December 21, 1999 3:27 PM

Summary of Contents for 2000 Islandia





























































































Search results

Summary of Contents for 2000 Islandia

Reviews:

Related manuals for 2000 Islandia

Brands by name

Popular brands

Sea-doo 2000 Islandia, Operator'S Manual

Search results

Summary of Contents for 2000 Islandia

Reviews:

Related manuals for 2000 Islandia

Brands by name

Popular brands