External Controls
E-19
Unauthorized disassembling and/or modification could
result in malfunction or flooding, and void product warranty.
Take the product to a SEA&SEA authorized service center
for repair or inspection.
Never expose the battery to flame or fire, or to excessive heat.
Never attempt to disassemble, alter or directly solder the battery.
There are no user-serviceable parts. Tampering with battery
may expose you to dangerous voltage, battery acid, or
electrical shock.
Never short-circuit the terminals of a battery, as it could result
in battery leakage, heat generation, fire, or explosion. Avoid
contact with all metal objects during transporting and storage.
Move leaking batteries away from fire or open flames
immediately. The leaked fluid and its vapor are combustible.
If the battery leakage contacts your skin or clothing, flush the
affected area repeatedly with clean water. It may irritate your
skin. Should it get into your eyes, immediately rinse them
with plenty of water, avoid rubbing and seek medical advice.
Never attempt to insert the battery upside down or backward,
as it could result in battery leakage or explosion. Always
confirm the direction of plus and minus before installation.
Never connect a battery directly to a plug outlet or car
cigarette lighter.
Use only batteries approved for use in this product. Do not
mix old and new batteries or batteries of different types.
Remove batteries before transport or storage, or when you
are not going to use the product for an extended period of
time, to prevent unexpected activation.
2
1
1
ON
OFF
ON
OFF
Set the power
switch to ON.
1
Press the test light button to confirm that it
lights up.
2
Set the power
switch to OFF.
1
If the forked tip of the sensor section is wet, wipe
it with dry cloth.
2
If it is not wiped off sufficiently, the LED lamp lights up
when the power is switched on.
When the leak sensor is not to be used for long time,
store it with the battery removed.
Make sure that the ends of the forked tip of the
sensor section are not in contact with each other.
The LED lamp lights as long as the test light
button is pressed. If it does not light up, replace
the battery with a new one.
If you will not use the product for an extended period of
time, store it away from high temperatures, high
humidity, direct sunlight, or extreme cold.
Do not store the product with naphthalene or camphor
mothballs, or in locations such as a laboratory where
chemicals are used. This environment can cause mold,
rust, corrosion or malfunction.
Always remove batteries from the product after use.
Set the battery
When inserting or replacing the battery, wipe off moisture on the leak sensor thoroughly and
make sure that your fingers are dry. Take extra care for water droplets from your hair and wet
suit. Otherwise, an electric shock, mold growth on the product, or malfunctioning may occur.
Using the Leak Sensor
Leak sensor
The leak sensor lights up in red when it detects leakage underwater. If it lights up,
surface without delay while ensuring your safety and once out of water remove the
camera from the housing.
Before use
After use
Maintenance and Storage
Keep dry.The battery is not waterproof, and may malfunction
if immersed in water or exposed to high levels of humidity.
Rusting of the internal mechanism can cause irreparable
damage.
Do not remove and/or damage the case of a battery. It may
cause battery leakage, overheating or explosion.
Never use batteries should you notice any changes such as
leakage, discoloration or deformation. When you notice the
situation as abnormal, discontinue use immediately and take the
product to a SEA&SEA authorized service center for inspection.
Keep out of reach of children to prevent accidental ingestion.
If swallowed, seek medical advice immediately.
Do not leave or use batteries in an extreme hot environment.
This may cause battery leakage, overheating or battery
performance deterioration.
Keep away from strong magnetic fields. Do not use or store
this product in the vicinity of equipment that generates strong
electro-magnetic radiation or magnetic fields. Strong static
charges or the magnetic fields could cause malfunction, or
affect the product's internal circuitry.
Avoid strong shocks/impacts or excess stress to batteries.
Dirt on the battery terminals can prevent the product from
functioning. Should the battery terminals become dirty, wipe
them with a clean, dry cloth before use.
Turn the equipment off after use. Remove batteries from the
equipment when not in use. Store in dry area with
temperatures ranging from 0 to 30°C (32 to 86°F).
If LED lamp turn red due to malfunction, turn switch to OFF
position and return back again to ON to resume normal operation.
DANGER
WARNING
CAUTION
LED lamp will only light
up when the sensor is
wet.
