SDC EntryCheck 930 Installation Instructions Manual Download Page 1 | Manualshive

Page: 1 / 12

SDC EntryCheck 930 Installation Instructions Manual Download Page 1

3580 Willow Lane, Westlake Village, CA 91361-4921 • (805) 494-0622 • Fax: (805) 494-8861
www.sdcsecurity.com • E-mail: [email protected]

P:\INSTALLATION INST\Access Control\INST-930.vsd 0505 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email [email protected]

INSTALLATION INSTRUCTIONS

Model 930 EntryCheck

™

The 930 EntryCheck

™

is an easy to program, easy to use, stand alone, self-contained system with features

suitable for basic access control requirements. Providing either a voltage output or dry contact closure, the 930 is
designed to control any fail-safe or fail-secure electric locking device.

The 930 features one master code and five user codes. One relay output is available to provide a variety of access
control configurations including single door access control, Gate/Garage Door control or other electronic equipment
control. The 930 also provides two ¼ Amp grounding outputs for a CCTV/Light Controller and Doorbell operation.

SECURITY DOOR CONTROLS

1
2
3
...
»

Summary of Contents for EntryCheck 930













Reviews:

No comments