REQUIRES 4 AAA BATTERIES
Read and follow operating instructions.
1. Do not mix old and new batteries.
2. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Nickel-cadmium) batteries.
3. Only batteries of the same or equivalent type as recommended are to be used.
4. Batteries are to be inserted with the correct polarity.
5. Exhausted batteries are to be removed from the product.
6. The supply terminals are not to be short-circuited.
7. Non-rechargeable batteries are not to be recharged.
8. Rechargeable batteries are to be removed from the product before being charged (if removable)
9. Rechargeable batteries are only to be charged under adult supervision.
10. Dispose of batteries safely.
11. Do not dispose of this product in a fire. The batteries inside may explode or leak.
12. Batteries should be changed by adults only.
CAUTION:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
**This device and its antenna must not be co-located or operating in conjunction with any other antenna
or transmitter.
This Class B digital apparatus complies with Canadian ICES-003. Conforms to ASTM F963 standard.
Contents and color may vary slightly from these shown. Please retain packaging for future reference.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
This device coplies with Part 15 of the FCC Rules. Opperation is subject to the following two conditions
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT
STEP A
1. Unscrew battery door on handle
2. Remove battery door from handle
STEP B
1. Insert batteries as shown in diagram.
3. Make sure the cloth pull-tab is inserted
under the batteries for easy removal.
2. Replace battery door on handle.
phillips head
screwdriver
Left Joystick
= Forward
= Backward
Right Joystick
= Gradual Left Turn
= Gradual Right Turn
Left + Right Joystick
+ = Forward Sharp Left Turn
+ = Forward Sharp Right Turn
+ = Backward Sharp Left Turn
+ = Backward Sharp Right Turn
Left + Right Joystick
C/OFF On
Left
Joystick
Right
Joystick
AAA LR03 (1.5V)
AAA LR03 (1.5V)
AAA LR03 (1.5V)
AAA LR03 (1.5V)
CHARGING / PAIRING INSTRUCTIONS
CONTROLLER INSTRUCTIONS
There are 2 ways to charge your RC Knuckle-Headz
1. Use USB Charger to charge your car. Turn car OFF and plug car into USB charger.
Charge car for about 25 minutes. The light on the bottom the car will turn red
while charging and will turn green when fully charged.
2. Use plug inside controller. Turn car OFF and controller to OFF to charge. Charge
car for about 25 minutes. The light on the bottom the car will turn red while
charging and will turn green when fully charged.
3. When fully charged, remove the USB charger or the plug inside controller from the
car. TIP: Always hold the plug when disconnecting. Never pull the cable to
disconnect; this may cause the cable to break.
1.
2.
BATTERY INSTALLATION
REQ
REQ
REQ
REQ
REQ
REQUIRES 4 AAA BATTERIES
2. Rem
em
emov
ov
ove
e
e ba
ba
batt
tt
tter
er
er
y do
do
door
or
or
fro
ro
rom
m
m ha
ha
ha
ndle
ST
3.
3.
Cloth pull-tab
Charging Cord
Race in
MINUTES!
Includes
USB
CHARGER CORD
/
/
TIP:
If car is not working, turn both car and controller to OFF for 5 seconds and
then turn both car and controller to ON.
/
/
Pairing:
1.
Turn controller to on. The red light on the controller will flash red.
2. Turn car to on. The red light on bottom of car will flash red.
3. When both lights turn turn off the car and controller are paired and ready for use.
4. When storing your Knuckle-Headz RC make sure to fully charge your car and then
turn the controller and the car to the off positions. This will help the batteries last
longer.
You can purchase replacement batteries at (800) 336-7745 or at sdtoyz.com/rcknuckleheadz/replacementbatteries
TIP:
It is best to use USB
charging cord as your AAA
batteries will last longer.
Pairing Light
Lorem ipsum
GENERAL BATTERY INFORMATION
This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured
not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government.
IC statement
This device complies with RSS210 of Industry Canada. Cet appareil se conforme à RSS210 de Canada d'Industrie. This
device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. appareils radio exempts de licence. Son fonctionnement
est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif
doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
