background image

Adding/Replacing Transmitters 

To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired

transmitters ready and follow the steps below. 

Note

: Up to 4 transmitters can be programmed to operate the system.  To erase any previously  stored

transmitter codes, be sure to program all 4 transmitter memory locations. 
To program the transmitter(s):

1.  Turn on the ignition key On, Off, On, Off, and back On. (Key On 3 times)

· The siren will chirp 3 times.

2.  Press and hold the Override switch for 5 seconds.

· The siren will chirp 5 times.
· The LED will illuminate.

3.  Press Button 1 on the first transmitter.

· The siren will chirp once.

4.  Press Button 1 on the first transmitter again.

· The siren will chirp twice to indicate it has learned the code.

5.  Repeat steps 3 and 4 for each transmitter (up to 4).  
6.  Turn off the ignition key.

Two Car Operation

If two vehicles are equipped with Galaxy 5000RS Plus systems, for convenience both can be operated using

the same remote transmitter.  If all four transmitters are to be used with both cars, program transmitters

A and B into the first vehicle in the manner described above.  Program transmitters C and D by pressing

the Shift button twice before performing steps 3 and 4 above.  

When finished programming the first vehicle, program transmitters C and D into the second vehicle as

normal, then program transmitters A and B by pressing the Shift button twice before performing steps 3

and 4 above. 

When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing

the Shift button twice and the desired function button. 

Battery Replacement

Your Galaxy Remote Transmitter uses a 12 volt alkaline battery (type 23A), which will require replacement

in time.  Depending on the amount of use, the battery may last up to six months or more before it needs

replacement. When the battery needs replacing, the system’s operating range will decrease or the

transmitter LED may not be as bright.

In order to change the battery, first remove 2 screws from the back of the transmitter and separate the top

and bottom halves of the case.  While replacing the battery make sure that the positive and negative

terminals are positioned correctly, then carefully reassemble the transmitter case.

Galaxy 5000RS Plus  -  Page 3

Summary of Contents for Galaxy 5000RS Plus Series

































Reviews: