background image

Page 12 -  Galaxy 2000RS Plus

Pin 13

WHITE/BLACK WIRE

:  Hood  Pin  Input  (-).  Connect  the  to  the  hood  pin  switch.  The  switch  must

provide a ground output when switch is opened.  

Pin 14

ORANGE WIRE

: Anti-Grind Output (-) 500 mA.  The Orange wire provides a ground output to activate

a relay for anti-grind protection. 

Pin 15

VIOLET/WHITE WIRE

: Factory Disarm Output (-) 500 mA. The Violet/white wire provides a ground

output on disarming and before remote starting to disarm a factory security system. Connect to the
wire that requires a ground pulse to disarm the factory security system. 

Pin 16

WHITE/VIOLET WIRE

: Factory Rearm Output (-) 500 mA. The White/violet wire provides a ground

output on remote start shutdown to rearm a factory security system. Connect to the wire that requires
a ground pulse to rearm the factory security system. 

Pin 17

BROWN WIRE

: Audible Status Output (+) 3A.  The Brown wire may be connected to an optional

audible status indicator such as a siren or piezo device.  

Pin 18

GRAY WIRE

: Auxiliary 1 Output (-) 500 mA. Connect to a relay for an optional feature such as trunk

release, etc.  This output may be programmed for momentary, timed, or latched operation.

Pin 19

WHITE WIRE

:  Parking  Light  Output  (+/-)  relay.  Connect  the  White  wire  to  the  circuit  that  shows

+12V or ground only when the parking lights are on and set the internal parking light relay jumper to
the proper polarity. For parking light circuits exceeding 10 amps, a relay is required. For vehicle’s with
independent left and right parking light circuits, diodes must be installed to keep the circuits separate.
NOTE: Do not connect the WHITE wire to the vehicle’s headlight circuit.

Pin 20

BROWN/WHITE WIRE

: Horn Output (-) 500 mA. Connect to a relay to honk the vehicle’s horn when

the panic feature is triggered.  This wire may instead be programmed as an ignition 3 relay trigger.

Plug-in Connectors

4-Pin White Connector: 

Auxiliary start input port for use with after-market security system.

· WHITE WIRE - 3 pulse remote start / Parking Brake (-) input.  

3 Pulse Remote Start Input: Connect to the door lock output from the keyless entry system.  When the
lock button is pressed 3 times the vehicle will start.  
Parking Brake Input: For vehicles equipped with a turbo charged engine, this wire must be connected to
the parking brake wire if using the optional Turbo Timer feature.  For vehicles with a positive parking brake
wire, a relay must be used to invert the polarity.

· BLUE WIRE - 1 pulse remote start (-) input.  Connect to auxiliary output from aftermarket alarm.
· RED WIRE - not used.
· BLACK WIRE - not used.

2-Pin Blue Connector: 

Valet switch port.  Mount switch where it is accessible from the driver’s position.

2-Pin Red Connector: 

LED port.  Mount LED where it may be easily seen from either side of the vehicle.

3-Pin White Door Lock Connector: 

Door lock port.

· BLUE WIRE - negative unlock output (-) 500mA.
· RED WIRE - (+) 100mA trigger output for optional plug-in door lock relay module,   
· GREEN WIRE - negative lock output (-) 500mA.

3-Pin Blue Network Connector:

The plug-in network connector port is located on the side of the main

module.  This network port may be used with the optional personal computer interface or Pocket PC for
diagnostics,  software  customization  and  expanded  programming  options.    The  network  also  offers
connection to several optional accessories.  

See your dealer for more information.

4-Pin White Flat Connector:

Antenna connector port.  

Summary of Contents for Galaxy 2000RS-MDL





























Reviews: