SCS PTC-IIex Manual Download Page 73

Page: 73 / 220

6 Commands

This command reads the PTC log entries. The last 16 PACTOR/AMTOR contacts are
displayed (except Unproto contacts). The Log entries can only be erased with a

RESTart

(a total reset).

The following extra information in the callsign field is also available:

S1:

PACTOR-I (Sysop call)

S2:

PACTOR-II (Sysop call)

AMTOR links are only entered in the Logbook after a successful

LOGIn

After the call the used scan channel (1-16) is displayed in a new column (CH) in the PTC-
Log. If the scanner was not activated a 0 is displayed as scan channel. The extended log is
only displayed if at least one of the shown connections was started out of a scan process
of the PTC.

Packet-Radio entries are shown with X (from AX.25) The logbook entries are made only
after a disconnect, so that by multiple simultaneous logged in users, the logbook entries
might not appear in strictly chronological order.

6.52

LOGIn

Remote

In order to allow access to the PTC mailbox in AMTOR, a user station must first Login
using the

LOGIn

command e.g.

LOGI

DL1ZAM. The user's callsign is thus made

available to the PTC mailbox. Only after a correct

LOGIn

can the AMTOR user station

send, read or delete files from the mailbox. A successful

LOGIn

also writes the user's

callsign into the Log book page.

LOGIn

can also be used by the sysop. This allows the callsign of the other station to be

entered into the PTC to enable full mailbox access, without the station having to go
through the full

LOGIn

procedure. In PACTOR, this would be needed only in

exceptional circumstances, as an automatic

LOGIn

is performed. The call of the other

station is essential for the correct operation of the PACTOR QRT protocol, so that
changes during a link could influence the QRT procedure.

In the STBY condition,

LOGIn

displays the call of the last connected station. This call

will also be used for a Connect command without argument. An argument (call) after

LOGIn

can be used to preset a call for the next master-connect without argument.

With a remote access using PACTOR, a

LOGIn

command will cause an error message.

6.53

MAil

Default setting: 0

Parameter: 0 New messages not reported.

1 New messages reported on connect.

Summary of Contents for PTC-IIex




























































































































































































































Search results

Summary of Contents for PTC-IIex

Reviews:

Related manuals for PTC-IIex

Brands by name

Popular brands

SCS PTC-IIex, Manual

Search results

Summary of Contents for PTC-IIex

Reviews:

Related manuals for PTC-IIex

Brands by name

Popular brands