SCS PTC-IIex Manual Download Page 69

Page: 69 / 220

6 Commands

This command starts an AMTOR FEC transmission (Mode-B). When the AMTOR
prompt is active, then this command has the same effect as the CHANGEOVER
character.

After approx. 4 minutes of pure idle transmissions, an automatic QRT is carried out.

6.42

FSKAmpl

Default setting: 60

Parameter: X 30... 3000, AF output voltage (peak to peak) in mV.

This serves to set the Audio output (transmitted signal) of the PTC-IIex for all non PSK
modes. Before this value is changed, the PSK amplitude should have been correctly set
(see

After the PSK amplitude has been correctly set, the transceiver MIC gain control
should

not

be further adjusted to attain the required power output for non PSK modes.

For this adjustment, (i.e. FSK/CW output power) exclusively use the

FSKAmpl

command. The transceiver should be connected either to a dummy load of appropriate
power handling capacity, or a well matched antenna. (please pay particular attention that
the chosen frequency is really free. Using

1 <Return> the Unproto mode 1 is started

(100 Bd FSK). Now, using the

FSKAmpl

command, (use the ESCAPE character to enter

the command mode before each change) adjust the audio output level of the PTC-IIex
until the required output power is reached (e.g. <ESC>

FSKA

100 <Return>). It should be

noted that the ALC level of the transceiver must not exceed the prescribed level (exactly
as with PSK). To prevent possible damage to the average TRX, caused by continuous
transmission, we recommend that the FSK output power should never exceed 50% of the
maximum PEP power. In the case of the average amateur transceiver of 100 watts, this
represents the 50 watt level. The internal impedance of the AF output stage of the PTC-
IIex is 330 Ohms and resistive.

6.43

HCr

Default setting: 0

Parameter: 0 Auto CHO after an empty line off.

1 Auto CHO after an empty line on.

HCr

is 1, then, in Hostmode, a CHANGEOVER is carried out after an empty line

(double <CR> or <Return>).

without parameters gives a list of all commands.

Summary of Contents for PTC-IIex




























































































































































































































Search results

Summary of Contents for PTC-IIex

Reviews:

Related manuals for PTC-IIex

Brands by name

Popular brands

SCS PTC-IIex, Manual

Search results

Summary of Contents for PTC-IIex

Reviews:

Related manuals for PTC-IIex

Brands by name

Popular brands