background image

TB-9098

 Page 5 of 7

© 2020 DESCO INDUSTRIES INC

Employee Owned

SCS 

- 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: 

StaticControl.com

Workstation 2 Operator Remote

724 Plus 

Workstation Monitor

Operator 

Remote Cable

Dual Operator Remote

Workstation 2 

Operator Remote

Operator 

Remote Cable

Figure 7. Cabling the Workstation 2 Operator Remote 

to the 724 Plus Workstation Monitor and Dual Operator 

Remote

When paired with the 724 Plus Workstation Monitor, 

the SCS 

770733

 Workstation 2 Operator Remote may 

be used to monitor a second operator at a nearby 

independent workstation. It allows the second operator 

to connect to his/her own operator remote rather than 

share the Dual Operator Remote included with the 724 

Plus Workstation Monitor. Use the following procedure 

to add the Workstation 2 Operator Remote to an 

existing 724 Plus Workstation Monitor setup.
1.  Disconnect the 724 Plus Workstation Monitor from 

power. 

2.  Determine the mounting location of the Workstation 

2 Operator Remote. Its jack should be accessible 

to the second operator. Locate it within reach of the 

included operator remote cable. Use its enclosure's 

mounting tabs to secure it underneath a table top or 

equipment. 

3.  Connect the operator remote cables to the 724 

Plus Workstation Monitor, Dual Operator Remote, 

and Workstation 2 Operator Remote as shown in   

Figure 7. 

4.  Insert the included black nylon plug into the operator 

2 jack located on the Dual Operator Remote. This 

will prevent operators from using this jack once the 

Workstation 2 Operator Remote is installed. 

 

NOTE: The operator 2 jack on the Dual Operator 

Remote must be plugged with the nylon plug when 

adding the Workstation 2 Operator Remote to the 

setup. The 724 Plus Workstation Monitor will alarm 

should it detect a Workstation 2 Operator Remote 

and vacant operator 2 jack on the Dual Operator 

Remote. 

5.  Reconnect the 724 Plus Workstation Monitor to 

power.

Figure 8. Inserting the black nylon plug into the operator 

2 jack on the Dual Operator Remote

Figure 6. SCS 

770733

 Workstation 2 Operator Remote

Summary of Contents for 724 Plus








Reviews: