background image

SL27M plissé 

contr

ol unit 

SL1807

Control unit 

This unit is used to control the polarity inversion necessary for

the correct function of the motor, which would not be realised

when using normal switches.

Each control unit can control one blind, or can simultaneously

control a group of up to four blinds, depending on the requi-

rements of the system. 

The limited dimensions of the unit allow its insertion inside the

standard electrical back box. 

It comprises an electronic card equipped with a protection fuse

that can be easily replaced.

Technical features

Dimensions (mm)

40x40x20

Input

Supply, marked as 

24V dc

Connection to the double switch or to the radio receiver, 

marked by a contact graphic

Connection from another control unit, marked as 

REMOTE

;

this is used only for centralised connections to other groups

(see note below)

Output

• 

Connection to the blind motor or to a bus line for 

connection towards other control units; marked as 

MOTOR

Fuse

6,3 A

Working temperature

-20 +60°C

14

Note

The 

REMOTE

terminal is available to allow the installer the opportunity to meet the client’s

requirements for a variety of group control combinations. This is achieved by connecting  the

REMOTE terminal to the MOTOR output terminal of another SL1807 CONTROL UNIT. A typical

application would be where a single control is required for a number in blinds already control-

led individually by a control unit. By connecting a new control unit via the  MOTOR output in

parallel with all the REMOTE  terminals of the existing control units involved in the total opera-

tion, the additional control unit, once has been activated, will control all the control units simul-

taneously, whilst still allowing control of each motor separately. 

Multiple control systems can be built up using this procedure. 

MOTOR

REMOTE

24 Vdc

CO

M
NO

CO

M
NO

A

B

A

B

MOTOR

REMOTE

24 Vdc

COM

NO

COM

NO

A

B

A

B

Output for

blind motor

Input for additional
control unit

Input for power supply

Input for connection to switches
and/or radio receiver

SL27M plissé_GB  15-05-2007  9:29  Pagina 14

Summary of Contents for SL27M
























Reviews: